Part two of my installation. Shows How to wire the Metra BT-5520 to add an amplifier to your stock stereo. Also shows the route taken for running speaker wires, and some tips for your installation. Thanks! Also check out my other videos for how to remove the Head Unit if you couldn't figure it out. The video was too long so I made a separate video for that. Materials Used: Panel Removal Kit Metra BT-5520 Wiring Harness Kicker ZX700.5 5 Channel Amplifier Kicker CK44 4-Channel Amp Install Kit (2x) Kicker ZISL (09ZISL) (Speaker Wire to RCA Conversion) Kicker ZXRC (10ZXRC) (Bass Remote Control) Single Subwoofer Box from SupercrewSound.com Alpine SWS-1043D Type-S Subwoofer 300w DVC @4ohms (4x) Infinity Kappa 682.9CF Door Speakers (6x9's) (100w @ 2ohms) **I used a roll of solder to fish the speaker wires through the side panels. I'm sure a coat hanger would work, but solder is more flexible and wont damage anything like a coat hanger might. **As noted in the video, if you used the same amplifier wiring kit, be aware that this kit comes with *barely enough* speaker wire to run through a supercrew. So don't leave a lot of slack on the ends as you will run out of wire. Any questions, leave in the comment section below. Thanks for watching!
Saturday, October 6, 2012
2010 F-150 Amplifier Installation Part Two
2010 F-150 Amplifier Installation Part Two Video Clips. Duration : 14.45 Mins.
Part two of my installation. Shows How to wire the Metra BT-5520 to add an amplifier to your stock stereo. Also shows the route taken for running speaker wires, and some tips for your installation. Thanks! Also check out my other videos for how to remove the Head Unit if you couldn't figure it out. The video was too long so I made a separate video for that. Materials Used: Panel Removal Kit Metra BT-5520 Wiring Harness Kicker ZX700.5 5 Channel Amplifier Kicker CK44 4-Channel Amp Install Kit (2x) Kicker ZISL (09ZISL) (Speaker Wire to RCA Conversion) Kicker ZXRC (10ZXRC) (Bass Remote Control) Single Subwoofer Box from SupercrewSound.com Alpine SWS-1043D Type-S Subwoofer 300w DVC @4ohms (4x) Infinity Kappa 682.9CF Door Speakers (6x9's) (100w @ 2ohms) **I used a roll of solder to fish the speaker wires through the side panels. I'm sure a coat hanger would work, but solder is more flexible and wont damage anything like a coat hanger might. **As noted in the video, if you used the same amplifier wiring kit, be aware that this kit comes with *barely enough* speaker wire to run through a supercrew. So don't leave a lot of slack on the ends as you will run out of wire. Any questions, leave in the comment section below. Thanks for watching!
Part two of my installation. Shows How to wire the Metra BT-5520 to add an amplifier to your stock stereo. Also shows the route taken for running speaker wires, and some tips for your installation. Thanks! Also check out my other videos for how to remove the Head Unit if you couldn't figure it out. The video was too long so I made a separate video for that. Materials Used: Panel Removal Kit Metra BT-5520 Wiring Harness Kicker ZX700.5 5 Channel Amplifier Kicker CK44 4-Channel Amp Install Kit (2x) Kicker ZISL (09ZISL) (Speaker Wire to RCA Conversion) Kicker ZXRC (10ZXRC) (Bass Remote Control) Single Subwoofer Box from SupercrewSound.com Alpine SWS-1043D Type-S Subwoofer 300w DVC @4ohms (4x) Infinity Kappa 682.9CF Door Speakers (6x9's) (100w @ 2ohms) **I used a roll of solder to fish the speaker wires through the side panels. I'm sure a coat hanger would work, but solder is more flexible and wont damage anything like a coat hanger might. **As noted in the video, if you used the same amplifier wiring kit, be aware that this kit comes with *barely enough* speaker wire to run through a supercrew. So don't leave a lot of slack on the ends as you will run out of wire. Any questions, leave in the comment section below. Thanks for watching!
Subscribe to:
Post Comments (Atom)
0 comments:
Post a Comment