This is my finished product after building a Mini-Kits EME117ver3 137MHz Weather Satellite Receiver. I enclosed the receiver board into a case purchased from Jaycar and added accessories such as power, Speaker volume, RX LED, Vernier precision potentiometer with analog dial for tuning and a backlit signal meter. An internal speaker is added so you can listen to the signal, but a secondary mono output connects from the back of the receiver to the soundcard the computer for reception and is set internally. RF comes in via a standard RF connector from the back with 50 Ohm impedance and the entire receiver runs from a 12V DC supply. A 500mA fuse has been added in the back panel for protection. I originally constructed a six position rotary channel switch which used six individual tuning pots for each frequency. Due to drift and the inability to tune to Doppler shift changes, I opted for the vernier dial control. The vernier dial is much simpler and only has three wires connected to the main receiver board and in circuit looks just like a single three pin pot. Overall the project is very good and a lot of fun to build. I currently am using only my amateur 2m/70cm Omni-directional antenna. It works but not so great once the satellites are overhead do to the flat angle of radiation my vertical antenna has. I plan to build a more specialised antenna soon called a Quadrifilar Helix Antenna that works very well for NOAA APT Reception and will make a big difference to the reception ...
Wednesday, October 31, 2012
0 commentsHome Constructed NOAA VHF Weather Satellite Receiver.
Home Constructed NOAA VHF Weather Satellite Receiver. Video Clips. Duration : 10.02 Mins.
This is my finished product after building a Mini-Kits EME117ver3 137MHz Weather Satellite Receiver. I enclosed the receiver board into a case purchased from Jaycar and added accessories such as power, Speaker volume, RX LED, Vernier precision potentiometer with analog dial for tuning and a backlit signal meter. An internal speaker is added so you can listen to the signal, but a secondary mono output connects from the back of the receiver to the soundcard the computer for reception and is set internally. RF comes in via a standard RF connector from the back with 50 Ohm impedance and the entire receiver runs from a 12V DC supply. A 500mA fuse has been added in the back panel for protection. I originally constructed a six position rotary channel switch which used six individual tuning pots for each frequency. Due to drift and the inability to tune to Doppler shift changes, I opted for the vernier dial control. The vernier dial is much simpler and only has three wires connected to the main receiver board and in circuit looks just like a single three pin pot. Overall the project is very good and a lot of fun to build. I currently am using only my amateur 2m/70cm Omni-directional antenna. It works but not so great once the satellites are overhead do to the flat angle of radiation my vertical antenna has. I plan to build a more specialised antenna soon called a Quadrifilar Helix Antenna that works very well for NOAA APT Reception and will make a big difference to the reception ...
This is my finished product after building a Mini-Kits EME117ver3 137MHz Weather Satellite Receiver. I enclosed the receiver board into a case purchased from Jaycar and added accessories such as power, Speaker volume, RX LED, Vernier precision potentiometer with analog dial for tuning and a backlit signal meter. An internal speaker is added so you can listen to the signal, but a secondary mono output connects from the back of the receiver to the soundcard the computer for reception and is set internally. RF comes in via a standard RF connector from the back with 50 Ohm impedance and the entire receiver runs from a 12V DC supply. A 500mA fuse has been added in the back panel for protection. I originally constructed a six position rotary channel switch which used six individual tuning pots for each frequency. Due to drift and the inability to tune to Doppler shift changes, I opted for the vernier dial control. The vernier dial is much simpler and only has three wires connected to the main receiver board and in circuit looks just like a single three pin pot. Overall the project is very good and a lot of fun to build. I currently am using only my amateur 2m/70cm Omni-directional antenna. It works but not so great once the satellites are overhead do to the flat angle of radiation my vertical antenna has. I plan to build a more specialised antenna soon called a Quadrifilar Helix Antenna that works very well for NOAA APT Reception and will make a big difference to the reception ...
Horntones Installation
Horntones Installation Video Clips. Duration : 10.18 Mins.
Chris Duke from Motorz TV www.motorz.tv demonstrates and shows you how to install Horntones, the ultimate MP3 player for your vehicle which plays your MP3s through an amplified loud speaker. Show notes: www.motorz.tv Website: www.motorz.tv Facebook: www.facebook.com Twitter: twitter.com
Chris Duke from Motorz TV www.motorz.tv demonstrates and shows you how to install Horntones, the ultimate MP3 player for your vehicle which plays your MP3s through an amplified loud speaker. Show notes: www.motorz.tv Website: www.motorz.tv Facebook: www.facebook.com Twitter: twitter.com
Jawbone Big Jambox review
Jawbone Big Jambox review Tube. Duration : 6.02 Mins.
Full review of the new Jawbone Big Jambox. Make sure to check out all the links down below to where you can pick this up. If you have any questions you can catch me on the social sites down below. Big thanks for watching the video and please don't forget to like, favorite and leave your comments with your thoughts. BUY YOUR'S HERE ALL THE LINKS ARE PROVIDED DOWN BELOW FOR YOUR CONVENIENCE. Big Jambox - Graphite Hex - amzn.to Big Jambox - White Wave - amzn.to Big Jambox - Red Dot - amzn.to CHECK OUT THE SITE- goo.gl FOLLOW ME ON THE SOCIAL SITE'S ALL THE LINKS DOWN BELOW. TWITTER- goo.gl FACEBOOK- goo.gl GOOGLE+ goo.gl
Full review of the new Jawbone Big Jambox. Make sure to check out all the links down below to where you can pick this up. If you have any questions you can catch me on the social sites down below. Big thanks for watching the video and please don't forget to like, favorite and leave your comments with your thoughts. BUY YOUR'S HERE ALL THE LINKS ARE PROVIDED DOWN BELOW FOR YOUR CONVENIENCE. Big Jambox - Graphite Hex - amzn.to Big Jambox - White Wave - amzn.to Big Jambox - Red Dot - amzn.to CHECK OUT THE SITE- goo.gl FOLLOW ME ON THE SOCIAL SITE'S ALL THE LINKS DOWN BELOW. TWITTER- goo.gl FACEBOOK- goo.gl GOOGLE+ goo.gl
Tuesday, October 30, 2012
0 commentsCustom Ammo Can Stereo Boombox
Custom Ammo Can Stereo Boombox Video Clips. Duration : 5.92 Mins.
A custom portable boombox I made from a 5.56mm ammunition can, a pair of car speakers, and a small car amplifier, and some spare parts.
A custom portable boombox I made from a 5.56mm ammunition can, a pair of car speakers, and a small car amplifier, and some spare parts.
EASY How TO Setup Surround sound
EASY How TO Setup Surround sound Video Clips. Duration : 4.05 Mins.
Easy how to Home Theater service set up on tv, video tutorial connect 5.1 or 7.1 speakers to home audio, diY review
Easy how to Home Theater service set up on tv, video tutorial connect 5.1 or 7.1 speakers to home audio, diY review
QSC K12 - **NEW** 1000 Watt Powered Speaker - Pro, Studio, DJ
QSC K12 - **NEW** 1000 Watt Powered Speaker - Pro, Studio, DJ Video Clips. Duration : 3.67 Mins.
www.agiprodj.com 866-PRO-MIXX (776-6499) DJ Ty Shows us the new QSC K12 1000 watt self powered loud speaker. Weighting in at only 41 pounds, this is an incredible speaker for the money and weight class alone - not to mention the 1000W amp! The QSC K Series of speakers includes a 1000W 2 way 8, 10 & 12 and a dual 12" Sub. Please Instant Message, email or call us toll for more info on these and other DJ Audio gear.
www.agiprodj.com 866-PRO-MIXX (776-6499) DJ Ty Shows us the new QSC K12 1000 watt self powered loud speaker. Weighting in at only 41 pounds, this is an incredible speaker for the money and weight class alone - not to mention the 1000W amp! The QSC K Series of speakers includes a 1000W 2 way 8, 10 & 12 and a dual 12" Sub. Please Instant Message, email or call us toll for more info on these and other DJ Audio gear.
Monday, October 29, 2012
0 commentsCar Audio 101 - Alternator Tutorial
Car Audio 101 - Alternator Tutorial Tube. Duration : 2.30 Mins.
DIY with Mike Stiers www.maxxsonics.com Back to Basics -- Car Audio 101 By Mike Stiers So you've decided to upgrade your car stereo system? A great deal of research and planning should go into this purchase since there is a lot to consider. Do you desire a nice upgrade of your factory speakers, are you looking for a Sound Quality overall of speakers, subwoofers and amplifiers, or are you designing a vision-blurring SPL machine? It is important to make a list of exactly what you are looking to replace or add to your audio system so that you can prepare your electrical system for the investment to come. Many people do not realize that their vehicles' factory electrical system was not designed for aftermarket audio equipment. In fact, most factory electrical systems can only handle an audio system of 600 to 1200 watts. The lower end of the scale being the smaller vehicles and most foreign rides, and the upper end being large trucks and sport utility vehicles. As you increase demand, you need to look at upgrading your battery, alternator and most importantly your "Big 3." ALTERNATORS The alternator powers the vehicle, all components and recharges the battery. A standard factory alternator ranges from 40 amps to 120 amps depending on vehicle. When the alternator is under high demand or the demand exceeds the alternators capability, your voltage will begin to fall and rely on the reserve of the battery. Lets use a 65 amp alternator for example in determining what aftermarket ...
DIY with Mike Stiers www.maxxsonics.com Back to Basics -- Car Audio 101 By Mike Stiers So you've decided to upgrade your car stereo system? A great deal of research and planning should go into this purchase since there is a lot to consider. Do you desire a nice upgrade of your factory speakers, are you looking for a Sound Quality overall of speakers, subwoofers and amplifiers, or are you designing a vision-blurring SPL machine? It is important to make a list of exactly what you are looking to replace or add to your audio system so that you can prepare your electrical system for the investment to come. Many people do not realize that their vehicles' factory electrical system was not designed for aftermarket audio equipment. In fact, most factory electrical systems can only handle an audio system of 600 to 1200 watts. The lower end of the scale being the smaller vehicles and most foreign rides, and the upper end being large trucks and sport utility vehicles. As you increase demand, you need to look at upgrading your battery, alternator and most importantly your "Big 3." ALTERNATORS The alternator powers the vehicle, all components and recharges the battery. A standard factory alternator ranges from 40 amps to 120 amps depending on vehicle. When the alternator is under high demand or the demand exceeds the alternators capability, your voltage will begin to fall and rely on the reserve of the battery. Lets use a 65 amp alternator for example in determining what aftermarket ...
How to Repair Headphone Wires
How to Repair Headphone Wires Video Clips. Duration : 6.47 Mins.
Hello, Welcome to my fourth installment to my Headphone Repair series. In this video I show how to fix the headphone wire itself. A lot of time a short can occur in the wire (instead of at the plug like I show in my other Headphone videos). Also, headphones wires can get cut or damaged very easily. This video shows you a simple way to make these types of repair. To purchase an inexpensive wire stripper and electrical tape, check out my Amazon Store. The link is located on my homepage on the right side or by clicking this link: astore.amazon.com
Hello, Welcome to my fourth installment to my Headphone Repair series. In this video I show how to fix the headphone wire itself. A lot of time a short can occur in the wire (instead of at the plug like I show in my other Headphone videos). Also, headphones wires can get cut or damaged very easily. This video shows you a simple way to make these types of repair. To purchase an inexpensive wire stripper and electrical tape, check out my Amazon Store. The link is located on my homepage on the right side or by clicking this link: astore.amazon.com
Wireless electricity transfer through electric resonance
Wireless electricity transfer through electric resonance Tube. Duration : 2.00 Mins.
-Input Signal: 188 KHz, square wave AC, 20 Volts Peak to Peak (Vpp) or 10 Volts Root Main Square (RMS) from a Signal Generator -Capacitors: Unpolarized, in parallel with coil (not mandatory to have capacitor at the transmitter, but increases slightly led brightness) -Coils: length=5 meters, diameter=1 mm, single wire, single layer, cylinder diameter= 12 cm, speaker cable for both transmitter & receiver (coil shape matters !!!) -LED: 1 bright 3Volt white LED at the receiver coil -Resonance occurs at more frequencies: 16, 20, 26, 36, 59, 188 KHZ (led is brightest at 188 KHz)
-Input Signal: 188 KHz, square wave AC, 20 Volts Peak to Peak (Vpp) or 10 Volts Root Main Square (RMS) from a Signal Generator -Capacitors: Unpolarized, in parallel with coil (not mandatory to have capacitor at the transmitter, but increases slightly led brightness) -Coils: length=5 meters, diameter=1 mm, single wire, single layer, cylinder diameter= 12 cm, speaker cable for both transmitter & receiver (coil shape matters !!!) -LED: 1 bright 3Volt white LED at the receiver coil -Resonance occurs at more frequencies: 16, 20, 26, 36, 59, 188 KHZ (led is brightest at 188 KHz)
Sunday, October 28, 2012
0 commentsBest Deadmau5 Head EVER!
Best Deadmau5 Head EVER! Video Clips. Duration : 3.73 Mins.
The deadmau5 head that I made and took to the concert at Soldier Field in Chicago! The thing on the ear is the backstage pass that Deadmau5 personally gave me himself, Joel and his manager both said it was one of the best one's that they have ever seen, and it was only the first one, of many to come, that I have ever made. He signed the back of the head, "Dood, best head EVER! Mau5 Joel Zimmerman"! He also wore it on stage during his set! I move around so much to demonstrate the stability and perfect fit of the Mau5head, which is fully ajdustable, so anyone can wear it!!! Sorry, the Tutorial video is taking longer than expected. In the mean Time here is a list of materials that I used to make this: 1 x 14" acrylic globe (I got mine from www.superiorlighting.com) 1 x 13' legth of sound activated EL wire (www.thatscoolwire.com) (with optional 12v battery pack) 1 x 17' legth of sound activated EL wire (I also bought clear plastic mounts for the mouth off of the same website) (also with optional additional 12v battery pack) 1 x Fully adjustable Hard hat (from Lowe's or similar) 2 x Skyballs for the eyes (from wallmart or similar) 1 x 1.5" thick insulation foam board (I got this from Lowe's, it only came in like a 4'x8' sheet) 1 x 0.5" thick styrofoam board (same deal as the insulation foam) 4 x threaded rods (about 1/4-3/8" thick, and at least 6" long) 16 x washers for the rods 16 x nuts for the rods 4-6 yds of fabric 0.5 yds sheer fabric (for the mouth) 1 x chicken wire (for ...
The deadmau5 head that I made and took to the concert at Soldier Field in Chicago! The thing on the ear is the backstage pass that Deadmau5 personally gave me himself, Joel and his manager both said it was one of the best one's that they have ever seen, and it was only the first one, of many to come, that I have ever made. He signed the back of the head, "Dood, best head EVER! Mau5 Joel Zimmerman"! He also wore it on stage during his set! I move around so much to demonstrate the stability and perfect fit of the Mau5head, which is fully ajdustable, so anyone can wear it!!! Sorry, the Tutorial video is taking longer than expected. In the mean Time here is a list of materials that I used to make this: 1 x 14" acrylic globe (I got mine from www.superiorlighting.com) 1 x 13' legth of sound activated EL wire (www.thatscoolwire.com) (with optional 12v battery pack) 1 x 17' legth of sound activated EL wire (I also bought clear plastic mounts for the mouth off of the same website) (also with optional additional 12v battery pack) 1 x Fully adjustable Hard hat (from Lowe's or similar) 2 x Skyballs for the eyes (from wallmart or similar) 1 x 1.5" thick insulation foam board (I got this from Lowe's, it only came in like a 4'x8' sheet) 1 x 0.5" thick styrofoam board (same deal as the insulation foam) 4 x threaded rods (about 1/4-3/8" thick, and at least 6" long) 16 x washers for the rods 16 x nuts for the rods 4-6 yds of fabric 0.5 yds sheer fabric (for the mouth) 1 x chicken wire (for ...
132894 / 1969 Ford Mustang
132894 / 1969 Ford Mustang Video Clips. Duration : 4.17 Mins.
For more information on this vehicle visit tinyurl.com This sinister 1969 Mustang pro-tourer is a take-no-prisoners muscle car which is ready to compete, drive or race anytime and anywhere! All of this Mustangs solid panels were stripped to bare metal and thoroughly worked to transform it from a nice piece of machinery into a trophy winning piece of art. Once that canvas was as close to perfect as possible, and displayed excellent fit and finish, a dynamic coat of Raven Black urethane was expertly applied, sealed in a glossy clearcoat shell and buffed to a fantastic shine. Pull the pins on this awesome Mustangs solid steel hood and you'll find an 800 horsepower, 557 cubic inch Jon Kaase V8 which twists out 750 lb./ft. of torque and wears some of the best aftermarket components on the planet. At the top of the engine, a bright blue air cleaner feeds a chrome 1050cfm Holley carburetor through a K&N reusable filter which sits just inside the cars fully functional hood scoop. Below that carburetor, a silver powder coated Jon Kaase alloy intake is bolted between Kaase Boss 9 aluminum heads which have been fitted with silver powder coated "Boss 557" valve covers and finished with chrome K&N crankcase breathers. Below those heads, 10.4 to 1 pistons combine with a roller cam to create explosive combustion; and in front of those heads, a reliable points distributor sends fire through blue Jon Kaase racing wires which have been fitted with MSD end caps. At the sides of the block ...
For more information on this vehicle visit tinyurl.com This sinister 1969 Mustang pro-tourer is a take-no-prisoners muscle car which is ready to compete, drive or race anytime and anywhere! All of this Mustangs solid panels were stripped to bare metal and thoroughly worked to transform it from a nice piece of machinery into a trophy winning piece of art. Once that canvas was as close to perfect as possible, and displayed excellent fit and finish, a dynamic coat of Raven Black urethane was expertly applied, sealed in a glossy clearcoat shell and buffed to a fantastic shine. Pull the pins on this awesome Mustangs solid steel hood and you'll find an 800 horsepower, 557 cubic inch Jon Kaase V8 which twists out 750 lb./ft. of torque and wears some of the best aftermarket components on the planet. At the top of the engine, a bright blue air cleaner feeds a chrome 1050cfm Holley carburetor through a K&N reusable filter which sits just inside the cars fully functional hood scoop. Below that carburetor, a silver powder coated Jon Kaase alloy intake is bolted between Kaase Boss 9 aluminum heads which have been fitted with silver powder coated "Boss 557" valve covers and finished with chrome K&N crankcase breathers. Below those heads, 10.4 to 1 pistons combine with a roller cam to create explosive combustion; and in front of those heads, a reliable points distributor sends fire through blue Jon Kaase racing wires which have been fitted with MSD end caps. At the sides of the block ...
Cyber Acoustics 3 pc Subwoofer/Satellite System CA-3602
Cyber Acoustics 3 pc Subwoofer/Satellite System CA-3602 Tube. Duration : 10.38 Mins.
Unboxing and setting up of the Cyber Acoustics 3 pc Subwoofer/Satellite System CA-3602 speakers.
Unboxing and setting up of the Cyber Acoustics 3 pc Subwoofer/Satellite System CA-3602 speakers.
Saturday, October 27, 2012
0 commentsCamaro Scosche Dash Kit Review
Camaro Scosche Dash Kit Review Video Clips. Duration : 7.43 Mins.
A quick overview of my install of the new Scosche Dash Kit for the 2010 - 2012 Camaro. I replaced my Metra kit with this and overall, I like it better so I'll be keeping it. The Good: * The install was MUCH easier than the Metra kit - basically plug and play (just follow the directions - not many wires to splice and there isn't another box you need to tuck under there. * Most importantly: the kit looks better than the Metra in my opinion, a little more like how a stock setup should have been for a 2010 Camaro (that old radio is UGLY and the metra was plain) * The touch screen controls work nice (although there's a little glare) and the steering wheel controls work like stock * Most of the car settings are supported and controlled within the touch screen (that's a separate unit for the Metra kit). The Bad: * The two pieces of the unit (face and bottom piece) are glued together and not all that well. It separated on me just a little. * Getting the head unit to fit right was a chore - had to screw the kit back in an out a few times and bend the brackets a bit to make it fit right. Even then, the gap at the top is a little more obvious than it should be. * The directions could have included some actual diagrams on how to get the center console / dash apart (instead of just text descriptions with part #s). * The speaker that produces the door chimes, blinkers, and back-up sensors is mounted somewhere inside the kit and sounds a little cheap * Doesn't come with Onstar support ...
A quick overview of my install of the new Scosche Dash Kit for the 2010 - 2012 Camaro. I replaced my Metra kit with this and overall, I like it better so I'll be keeping it. The Good: * The install was MUCH easier than the Metra kit - basically plug and play (just follow the directions - not many wires to splice and there isn't another box you need to tuck under there. * Most importantly: the kit looks better than the Metra in my opinion, a little more like how a stock setup should have been for a 2010 Camaro (that old radio is UGLY and the metra was plain) * The touch screen controls work nice (although there's a little glare) and the steering wheel controls work like stock * Most of the car settings are supported and controlled within the touch screen (that's a separate unit for the Metra kit). The Bad: * The two pieces of the unit (face and bottom piece) are glued together and not all that well. It separated on me just a little. * Getting the head unit to fit right was a chore - had to screw the kit back in an out a few times and bend the brackets a bit to make it fit right. Even then, the gap at the top is a little more obvious than it should be. * The directions could have included some actual diagrams on how to get the center console / dash apart (instead of just text descriptions with part #s). * The speaker that produces the door chimes, blinkers, and back-up sensors is mounted somewhere inside the kit and sounds a little cheap * Doesn't come with Onstar support ...
Best Bluetooth Compact Speakers (Jawbone Jambox, Soundmatters foxLv2, Monster ClarityHD, Satechi)
Best Bluetooth Compact Speakers (Jawbone Jambox, Soundmatters foxLv2, Monster ClarityHD, Satechi) Tube. Duration : 15.12 Mins.
More info at www.jessebandersen.com
More info at www.jessebandersen.com
Friday, October 26, 2012
0 commentsGTA Car Kits - Mazda CX7 2007, 2008, 2009, 2010, 2011, 2012 install of iPhone, iPod and iPad adapter
GTA Car Kits - Mazda CX7 2007, 2008, 2009, 2010, 2011, 2012 install of iPhone, iPod and iPad adapter Tube. Duration : 10.83 Mins.
www.gtacarkits.com - installation instruction for iPhone, iPod and iPad adapter into factory stereo of Mazda CX7 2007, 2008, 2009, 2010, 2011 and 2012 model years. After installing the car kit you would be able to listen to your iPod, iPhone or iPad through your factory stereo speakers and control your music through controls on the factory radio or steering wheel. For 2009 and up models - the kits also displays the playlist number and song name. You can also use these video instructions for removing your Mazda CX7 factory stereo.
www.gtacarkits.com - installation instruction for iPhone, iPod and iPad adapter into factory stereo of Mazda CX7 2007, 2008, 2009, 2010, 2011 and 2012 model years. After installing the car kit you would be able to listen to your iPod, iPhone or iPad through your factory stereo speakers and control your music through controls on the factory radio or steering wheel. For 2009 and up models - the kits also displays the playlist number and song name. You can also use these video instructions for removing your Mazda CX7 factory stereo.
4 Channel Amp Install Tips - Front To Rear Jump
4 Channel Amp Install Tips - Front To Rear Jump Tube. Duration : 8.02 Mins.
Try this trick to get the job done ALOT quicker and save alot on your wire usage too!
Try this trick to get the job done ALOT quicker and save alot on your wire usage too!
Pyle Audio PLMCA60
Pyle Audio PLMCA60 Tube. Duration : 3.23 Mins.
Hey all- this is a quick movie of putting a brand new Pyle Audio PLMCA60 onto my Harley. This is basically the most complete mp3 kit I could find for a Motorcycle- has everything from the usb charger to an ipod holder- 600w of sound and sharp looking bullet speakers that are weatherproof- I hope my install vid is useful.
Hey all- this is a quick movie of putting a brand new Pyle Audio PLMCA60 onto my Harley. This is basically the most complete mp3 kit I could find for a Motorcycle- has everything from the usb charger to an ipod holder- 600w of sound and sharp looking bullet speakers that are weatherproof- I hope my install vid is useful.
Thursday, October 25, 2012
0 commentsBuilding Box & Bloody Disasters - HUGE Single 18 Ascendant Car Audio MAYHEM Ported Sub EXO Enclosure
Building Box & Bloody Disasters - HUGE Single 18 Ascendant Car Audio MAYHEM Ported Sub EXO Enclosure Tube. Duration : 3.12 Mins.
Subwoofer box almost complete! Video Cut Short Due To Injury ;) www.youtube.comEnjoy The Music? Subscribe For More ORIGINAL Tracks! "When I'm In The Mood" - By Cultivata Beats Chillin' Beat Made On FL Studio 8 www.youtube.com My First Car Audio SPL Bass Installation (1) Alpine MRP 500 - Class D Monoblock Amplifier (1) Alpine MRP 1000 - Class D Monoblock Amplifier (3) Orion HP 12 @ 2 ohms - Subs (2) Orion Cobalt 5.25's - Highs (2) Power Acoustik PCX 5 farad Capacitors *Same 200 amp H/O Alt* My Current Competition Car Audio Stereo System Pioneer DEH-P6000ub - Head Unit (1) Clarion Eqs746 Graphic EQ - BEST Equalizer (2) Orion Cobalt 5.25's - Highs & Tweeters (2) Polk DB 5x7's - Mid Range Speakers (2) Polk DB 6x9's - Mid Range Speakers (1) DAT Hellfire 2500.1 Class D Mono Amp / Diablo Audio Technologies = 3000 + Watts RMS @ 1 ohm (1) Ascendant Audio Mayhem 18 inch Subwoofer (1) Single Slot Ported Box Tuned To 32 hz @ 6cft (1) MCR 200 amp High Output Alternator Big 3 / 0 Gauge Cable - Stinger / Tsunami Power Wire BASSHEADS UNITE! Make Em' Know Technology ! ~ EXO It all started when I was young. I loved that deep sounding bass you hear at the movie theater, the type that tickles your ears and shakes windows it's so loud. I was soon to be addicted to all car audio stereo systems in whole new light cheap, or expensive. Ever since I could wire my first subwoofer tinsel leads, I've been getting loud ever since. I love intense songs that have a lot of really hard hitting, deepest ...
Subwoofer box almost complete! Video Cut Short Due To Injury ;) www.youtube.comEnjoy The Music? Subscribe For More ORIGINAL Tracks! "When I'm In The Mood" - By Cultivata Beats Chillin' Beat Made On FL Studio 8 www.youtube.com My First Car Audio SPL Bass Installation (1) Alpine MRP 500 - Class D Monoblock Amplifier (1) Alpine MRP 1000 - Class D Monoblock Amplifier (3) Orion HP 12 @ 2 ohms - Subs (2) Orion Cobalt 5.25's - Highs (2) Power Acoustik PCX 5 farad Capacitors *Same 200 amp H/O Alt* My Current Competition Car Audio Stereo System Pioneer DEH-P6000ub - Head Unit (1) Clarion Eqs746 Graphic EQ - BEST Equalizer (2) Orion Cobalt 5.25's - Highs & Tweeters (2) Polk DB 5x7's - Mid Range Speakers (2) Polk DB 6x9's - Mid Range Speakers (1) DAT Hellfire 2500.1 Class D Mono Amp / Diablo Audio Technologies = 3000 + Watts RMS @ 1 ohm (1) Ascendant Audio Mayhem 18 inch Subwoofer (1) Single Slot Ported Box Tuned To 32 hz @ 6cft (1) MCR 200 amp High Output Alternator Big 3 / 0 Gauge Cable - Stinger / Tsunami Power Wire BASSHEADS UNITE! Make Em' Know Technology ! ~ EXO It all started when I was young. I loved that deep sounding bass you hear at the movie theater, the type that tickles your ears and shakes windows it's so loud. I was soon to be addicted to all car audio stereo systems in whole new light cheap, or expensive. Ever since I could wire my first subwoofer tinsel leads, I've been getting loud ever since. I love intense songs that have a lot of really hard hitting, deepest ...
PLEXIGLASS Subwoofer Box w/ Insane Earthquake Car Audio System | 12" EQ Subs / 2 PowerHouse SQ AMPS
PLEXIGLASS Subwoofer Box w/ Insane Earthquake Car Audio System | 12" EQ Subs / 2 PowerHouse SQ AMPS Tube. Duration : 2.18 Mins.
Checking Out A WICKED Clean Car Audio Install! Thanks For Rating & Subscribing! www.youtube.com Music By: Kevin Macleod Song: "Look Busy" incompetech.com Licensed under Creative Commons "Attribution 3.0" creativecommons.org Screamin' Eagles Plexiglass Subwoofer Box! Now I want to see the Kompressor 10" & BP112 For SPL ! BassHeads Unite!
Checking Out A WICKED Clean Car Audio Install! Thanks For Rating & Subscribing! www.youtube.com Music By: Kevin Macleod Song: "Look Busy" incompetech.com Licensed under Creative Commons "Attribution 3.0" creativecommons.org Screamin' Eagles Plexiglass Subwoofer Box! Now I want to see the Kompressor 10" & BP112 For SPL ! BassHeads Unite!
Building 4x12" Speaker Guitar Cabinet
Building 4x12" Speaker Guitar Cabinet Tube. Duration : 8.42 Mins.
How to build easily a 4x12" guitar cabinet at home using just a few tools. Custom built guitar cabinets at openskyprod@yahoo.com www.nimrodsweapon.com
How to build easily a 4x12" guitar cabinet at home using just a few tools. Custom built guitar cabinets at openskyprod@yahoo.com www.nimrodsweapon.com
Wednesday, October 24, 2012
0 commentsHook Up A Car Stereo In Your House Without PSU (Easiest Way)
Hook Up A Car Stereo In Your House Without PSU (Easiest Way) Tube. Duration : 14.22 Mins.
The easiest way to hook up a car stereo in your house, by using a 12DC power supply converter. Audio: No copyright infringement intended - I DO NOT OWN ANY AUDIO IN THIS VIDEO. Audio: Nickelback - When We Stand Together Maroon 5 ft Christina Aguilera - Moves Like Jagger (Radio 96.3 Heart SX) Belinda Carlisle - Heaven Is A Place On Earth Frederik Olufsen - Rocks CD Used: Nickelback - Here & Now Budget Car Stereos - www.amazon.co.uk www.amazon.co.uk www.amazon.co.uk AND MY FAVOURITE! - www.amazon.co.uk (This Is The One I Have Installed In My Own Car & Very Pleased With It) 12v Power Supply: www.amazon.co.uk Affordable Car Speakers: www.amazon.co.uk www.amazon.co.uk www.amazon.co.uk Speaker Wire: www.amazon.co.uk www.amazon.co.uk Electrical Tape Under £2! (Price Subject To Change): www.amazon.co.uk Anti-Static Wrist Band Also Under £2!: www.amazon.co.uk Crocodile Clip For Testing: www.amazon.co.uk Cable Cutters: www.amazon.co.uk On/Off Rocker Switches Under £3!: www.amazon.co.uk Super Glue: www.amazon.co.uk Soldering Iron Under £9!: www.amazon.co.uk PC Fan: www.amazon.co.uk Cable Splicers: www.amazon.co.uk Amazon Items Listed Above I Have Purchased To Complete My Set Up Of A Car Stereo In The Home, If You Already Have A Stereo To Hook Up In Your House, It Won't Cost More Than £30.00! Please Note: Amazon Prices Are Subject To Change! This Is The Stereo I Used In The Video, Which Comes With Two Speakers & A Remote!: www.argos.co.uk It's Currently £53.99 Which Is A Steal, I ...
The easiest way to hook up a car stereo in your house, by using a 12DC power supply converter. Audio: No copyright infringement intended - I DO NOT OWN ANY AUDIO IN THIS VIDEO. Audio: Nickelback - When We Stand Together Maroon 5 ft Christina Aguilera - Moves Like Jagger (Radio 96.3 Heart SX) Belinda Carlisle - Heaven Is A Place On Earth Frederik Olufsen - Rocks CD Used: Nickelback - Here & Now Budget Car Stereos - www.amazon.co.uk www.amazon.co.uk www.amazon.co.uk AND MY FAVOURITE! - www.amazon.co.uk (This Is The One I Have Installed In My Own Car & Very Pleased With It) 12v Power Supply: www.amazon.co.uk Affordable Car Speakers: www.amazon.co.uk www.amazon.co.uk www.amazon.co.uk Speaker Wire: www.amazon.co.uk www.amazon.co.uk Electrical Tape Under £2! (Price Subject To Change): www.amazon.co.uk Anti-Static Wrist Band Also Under £2!: www.amazon.co.uk Crocodile Clip For Testing: www.amazon.co.uk Cable Cutters: www.amazon.co.uk On/Off Rocker Switches Under £3!: www.amazon.co.uk Super Glue: www.amazon.co.uk Soldering Iron Under £9!: www.amazon.co.uk PC Fan: www.amazon.co.uk Cable Splicers: www.amazon.co.uk Amazon Items Listed Above I Have Purchased To Complete My Set Up Of A Car Stereo In The Home, If You Already Have A Stereo To Hook Up In Your House, It Won't Cost More Than £30.00! Please Note: Amazon Prices Are Subject To Change! This Is The Stereo I Used In The Video, Which Comes With Two Speakers & A Remote!: www.argos.co.uk It's Currently £53.99 Which Is A Steal, I ...
Speakon Connector Installation.m4v
Speakon Connector Installation.m4v Tube. Duration : 8.60 Mins.
Ross Henning from Tunes 4 My Party details the process of installing a Speakon connector on a professional speaker cable. If you are in need of a Houston Disc Jockey, please visit our website at www.tunes4myparty.com
Ross Henning from Tunes 4 My Party details the process of installing a Speakon connector on a professional speaker cable. If you are in need of a Houston Disc Jockey, please visit our website at www.tunes4myparty.com
How To Make Homemade Fuse Blocks - Cheap Car Audio Install Tricks - Cool 0 Gauge ANL Holder Upgrade
How To Make Homemade Fuse Blocks - Cheap Car Audio Install Tricks - Cool 0 Gauge ANL Holder Upgrade Video Clips. Duration : 3.98 Mins.
Ever been stuck on a project because you don't have enough fuse blocks? Why pay when you can make your own! It's wicked easy & the plastic ones are no better! www.youtube.comEnjoy The Music? Subscribe For More ORIGINAL Tracks! "Conquer The World" - By Cultivata Beats Beat Made On FL Studio 8 www.youtube.com BTW - The solder reference is for when connecting wire into the terminals, So for you, yes it will be wicked needed. **Enjoy The Music? Subscribe For More Information On These ORIGINAL Tracks - Cultivata & MC Fathom Phantom** Step 1: Cut to length your 3/4 inch wood sliver to fit your applied fuse ( ANL ) Step 2: Mark & Drill 2 holes for the mouting bolts - matching the spot up with the eye. Step 3: Use a 1/2 inch butteryfly bit to shave down the existing hole by 1/4 inch ( This allows for Flush Mounted Heads ) Step 4: Drill 2, 2 inch by 5/8 inch fine thread screws into each hole, threading will occur naturally. Step 5: Then take 2 lug fasteners and find prefered fuse location along the 2" bolt. Step 6: Place fuse onto post, and screw on 2 more addition lugs. ( This will affix the fuse to the post firmly & securly ) Step 7: ( At This Point, solder the terminals onto your wire ) I will be getting some soon! Step 8: Fill the back of the fuse block with wood filler! ( This will prevent grounding out ) Step 9: Place terminals over post, and screw on 2 more additional lugs ( This will affix the terminals to the post firmly & securly ) Step 10: ENJOY! My First Car Audio ...
Ever been stuck on a project because you don't have enough fuse blocks? Why pay when you can make your own! It's wicked easy & the plastic ones are no better! www.youtube.comEnjoy The Music? Subscribe For More ORIGINAL Tracks! "Conquer The World" - By Cultivata Beats Beat Made On FL Studio 8 www.youtube.com BTW - The solder reference is for when connecting wire into the terminals, So for you, yes it will be wicked needed. **Enjoy The Music? Subscribe For More Information On These ORIGINAL Tracks - Cultivata & MC Fathom Phantom** Step 1: Cut to length your 3/4 inch wood sliver to fit your applied fuse ( ANL ) Step 2: Mark & Drill 2 holes for the mouting bolts - matching the spot up with the eye. Step 3: Use a 1/2 inch butteryfly bit to shave down the existing hole by 1/4 inch ( This allows for Flush Mounted Heads ) Step 4: Drill 2, 2 inch by 5/8 inch fine thread screws into each hole, threading will occur naturally. Step 5: Then take 2 lug fasteners and find prefered fuse location along the 2" bolt. Step 6: Place fuse onto post, and screw on 2 more addition lugs. ( This will affix the fuse to the post firmly & securly ) Step 7: ( At This Point, solder the terminals onto your wire ) I will be getting some soon! Step 8: Fill the back of the fuse block with wood filler! ( This will prevent grounding out ) Step 9: Place terminals over post, and screw on 2 more additional lugs ( This will affix the terminals to the post firmly & securly ) Step 10: ENJOY! My First Car Audio ...
Tuesday, October 23, 2012
0 commentsHow to Set Up PA Systems : Common Connectors for PA Systems
How to Set Up PA Systems : Common Connectors for PA Systems Tube. Duration : 2.83 Mins.
From XLR cables to RCA connectors and more, learn all about common cables and connectors used in setting up PA sound systems in this free professional music video from an expert PA system designer. Expert: Kip Bradford Bio: Kip Bradford has earned his living as a musician and sound system designer consultant.
From XLR cables to RCA connectors and more, learn all about common cables and connectors used in setting up PA sound systems in this free professional music video from an expert PA system designer. Expert: Kip Bradford Bio: Kip Bradford has earned his living as a musician and sound system designer consultant.
(HD) Alvin Lucier: Nothing is Real for piano, amplified teapot, recorder, & mini-sound system
(HD) Alvin Lucier: Nothing is Real for piano, amplified teapot, recorder, & mini-sound system Video Clips. Duration : 9.07 Mins.
My music and teaching blog: mostlynoise.wordpress.com flavors.me kriskerzman.tumblr.com sites.google.com HD version I am playing this ethereal and subtle work on my 2010-2011 recitals. I filmed my last performance in October, however, the technical challenges of playing and recording in addition to getting the amplification right were too great. So I restaged a recording in the chapel at Loyola High School, Los Angeles, where I teach. A few words of unsolicited advice for others wanting to play this piece: I spent quite a bit of time experimenting with different speaker/teapot combinations to find a pair that best expressed the harmonics. As a general rule, I found that the rounder teapots worked best, but they tend to have small lids, making it difficult to get the speaker inside. I used Blu-Tak to affix the speaker to the bottom of the pot. For this particular pot, the spout was too small to get the plug through, as well. So I had to cut the wire, thread the line through the teapot, then reattach it to another line. I have tried several different mics to amplify the pot, too. Generally, small diaphragm condensers work best. I had many problems, however, with feedback. For this video, I used a Shure SM58 directly into a powered JBL speaker. The very good off axis rejection of this mic eliminates feedback, but it is not very sensitive. For the recording, I placed a portable Sony recorder close-by and mixed it into the soundtrack as best I could with iMovie. I will be ...
My music and teaching blog: mostlynoise.wordpress.com flavors.me kriskerzman.tumblr.com sites.google.com HD version I am playing this ethereal and subtle work on my 2010-2011 recitals. I filmed my last performance in October, however, the technical challenges of playing and recording in addition to getting the amplification right were too great. So I restaged a recording in the chapel at Loyola High School, Los Angeles, where I teach. A few words of unsolicited advice for others wanting to play this piece: I spent quite a bit of time experimenting with different speaker/teapot combinations to find a pair that best expressed the harmonics. As a general rule, I found that the rounder teapots worked best, but they tend to have small lids, making it difficult to get the speaker inside. I used Blu-Tak to affix the speaker to the bottom of the pot. For this particular pot, the spout was too small to get the plug through, as well. So I had to cut the wire, thread the line through the teapot, then reattach it to another line. I have tried several different mics to amplify the pot, too. Generally, small diaphragm condensers work best. I had many problems, however, with feedback. For this video, I used a Shure SM58 directly into a powered JBL speaker. The very good off axis rejection of this mic eliminates feedback, but it is not very sensitive. For the recording, I placed a portable Sony recorder close-by and mixed it into the soundtrack as best I could with iMovie. I will be ...
Monday, October 22, 2012
0 commentsRear Speaker Removal
Rear Speaker Removal Tube. Duration : 5.42 Mins.
Rear Speaker Removal Saturn SL
Rear Speaker Removal Saturn SL
EXO Car Audio Updates & HHR BASS FLEX w/ Michelles Loudest Stereo System YET! 2 15" HDC4 Subs 4k RMS
EXO Car Audio Updates & HHR BASS FLEX w/ Michelles Loudest Stereo System YET! 2 15" HDC4 Subs 4k RMS Video Clips. Duration : 6.93 Mins.
Well guys, she's at it again! Here's some quick updates and a little video of Michelle's new install with 2 15" HDC4's on just over 4000 watts! Want More? Check Out My 2nd Channel For More Videos & Updates! www.youtube.com Thanks For Rating & Subscribing! www.youtube.com Demo Songs Used In This Video "From The Deep" by Bass Mekanik "Bass Groove 808" by Bassotronics "Gay Fish" by South Park (Kanye West Diss) Rucka Rucka Ali ? Outro Beat by T-Mic Beats!! Song: "Dime Piece" www.youtube.com www.soundclick.com/bands/default.cfm?bandID=780373 Techforce Michelle's 2006 Chevy HHR 4k RMS "Subsonique" by Dominic Iraggi & TFS 1 Iraggi 300 Amp High Output Alternator 2 Shuriken BT120 Batteries 2 15" Audioque HDC4 Subwoofers Techforce Services Decals 2 AQ 2200d's / AQ2200d Pioneer GPS Head Unit Oxygen Audio 4 Channel Memphis Speakers 4000 WATTS OF MASSIVE LOWS! My Upcoming BASS System! (2) DC Power Alternators / Soon to Be 270XP Pioneer Double Din Deck 6 Soundstream XXX Woofers 6 SS TX1.2600d Amps 6 Crescendo 8" Mid Drivers 6 Crescendo Tweeters 1 Oxygen Audio 4 Channel Amp 10 Batteries 300 Feet of 0 Gauge Power Wire Music By: Kevin Macleod Song: "Fluffing A Duck" incompetech.com Licensed under Creative Commons "Attribution 3.0" creativecommons.org EXOcontralto Bassheads Unite 2012
Well guys, she's at it again! Here's some quick updates and a little video of Michelle's new install with 2 15" HDC4's on just over 4000 watts! Want More? Check Out My 2nd Channel For More Videos & Updates! www.youtube.com Thanks For Rating & Subscribing! www.youtube.com Demo Songs Used In This Video "From The Deep" by Bass Mekanik "Bass Groove 808" by Bassotronics "Gay Fish" by South Park (Kanye West Diss) Rucka Rucka Ali ? Outro Beat by T-Mic Beats!! Song: "Dime Piece" www.youtube.com www.soundclick.com/bands/default.cfm?bandID=780373 Techforce Michelle's 2006 Chevy HHR 4k RMS "Subsonique" by Dominic Iraggi & TFS 1 Iraggi 300 Amp High Output Alternator 2 Shuriken BT120 Batteries 2 15" Audioque HDC4 Subwoofers Techforce Services Decals 2 AQ 2200d's / AQ2200d Pioneer GPS Head Unit Oxygen Audio 4 Channel Memphis Speakers 4000 WATTS OF MASSIVE LOWS! My Upcoming BASS System! (2) DC Power Alternators / Soon to Be 270XP Pioneer Double Din Deck 6 Soundstream XXX Woofers 6 SS TX1.2600d Amps 6 Crescendo 8" Mid Drivers 6 Crescendo Tweeters 1 Oxygen Audio 4 Channel Amp 10 Batteries 300 Feet of 0 Gauge Power Wire Music By: Kevin Macleod Song: "Fluffing A Duck" incompetech.com Licensed under Creative Commons "Attribution 3.0" creativecommons.org EXOcontralto Bassheads Unite 2012
EEVblog #29 - Audiophile Audiophoolery
EEVblog #29 - Audiophile Audiophoolery Tube. Duration : 9.97 Mins.
Dave cuts loose on the Golden Ear Audiophiles and all their Audiophoolery snake oil rubbish. Directional cables, thousand dollar IEC power cables, and all that rubbish. Monster Cable gets mostered. Panasonic gets a serve too, or is that applause? The Blue Jeans cable letter: www.audioholics.com
Dave cuts loose on the Golden Ear Audiophiles and all their Audiophoolery snake oil rubbish. Directional cables, thousand dollar IEC power cables, and all that rubbish. Monster Cable gets mostered. Panasonic gets a serve too, or is that applause? The Blue Jeans cable letter: www.audioholics.com
Sunday, October 21, 2012
0 commentsHow to Peter Green Mod a Les Paul Style Guitar
How to Peter Green Mod a Les Paul Style Guitar Video Clips. Duration : 10.23 Mins.
In this video I use an Agile AL-3100 to demonstrate how to turn the magnet around in a humbucker to take the pickup out of phase magnetically, and create that Peter Green or Gary Moore signature tone when both pickups are active and the volume pots are set to the same volume for each pickup. Gear used: Agile AL-3100 Guitar - Stock humbuckers Phaez Amp - Trainwreck Rocket Clone (For results demo at end) Celestion Super 65 Speaker in a homemade speaker cab I apologize for the blur or "blair witch" motion in some of the clips. I had to hold the flip camera and do the work at the same time for some of this, and I wasn't able to see the screen to see that it was blurry. I don't suspect it will be a problem. You should be able to see all the necessary shots. DISCLAIMER! Proceed at your own risk. You can ruin a pickup very easily if you're not careful!!
In this video I use an Agile AL-3100 to demonstrate how to turn the magnet around in a humbucker to take the pickup out of phase magnetically, and create that Peter Green or Gary Moore signature tone when both pickups are active and the volume pots are set to the same volume for each pickup. Gear used: Agile AL-3100 Guitar - Stock humbuckers Phaez Amp - Trainwreck Rocket Clone (For results demo at end) Celestion Super 65 Speaker in a homemade speaker cab I apologize for the blur or "blair witch" motion in some of the clips. I had to hold the flip camera and do the work at the same time for some of this, and I wasn't able to see the screen to see that it was blurry. I don't suspect it will be a problem. You should be able to see all the necessary shots. DISCLAIMER! Proceed at your own risk. You can ruin a pickup very easily if you're not careful!!
Tutorial: AV Receivers and Amps Auto EQ Set up
Tutorial: AV Receivers and Amps Auto EQ Set up Tube. Duration : 8.57 Mins.
Home cinema expert Neil Davidson explains the set up process for auto EQ systems like Audyssey. To comment on this video, go to www.avforums.com
Home cinema expert Neil Davidson explains the set up process for auto EQ systems like Audyssey. To comment on this video, go to www.avforums.com
Saturday, October 20, 2012
0 commentsAesop Rock - Night Light
Aesop Rock - Night Light Tube. Duration : 4.28 Mins.
Lyrics: Voice: "Day turns Night" x8 [Aesop Rock] Night Light suckas.. Put one up shackle me, not clean logic procreation I did invent the wheel, in a previous generation While the triple sixers lassos keep angels roped in the basement I locate my old halos and pass em out to the pavement Y'all catch a 30-second flash frame Dirty cooperative Neptune bloom head-trip split Fantastic! Fathom the splicing of major league low lifes With anti hero earthworm mentality (Godzilla!) I paste my game to zero all completion See a cretin's still a cretin even speakin' altered moniker American nightmare lost in the monitor I'll hold the door open so you can stagger through Then ten berserk and bread cookies in after you It's the gutter and I spell it with the 'G' I stole from "Get the fuck up" Noise crutch stolen wretched refuse of my teaming dumb luck Still I promise temperance storm breed still bleeding Amish See the freaks sucked out the wattage while 3 bears invade the cottage And I can't sleep now Yeah, the police'll laugh You won't be laughing when your covered wagons crash You won't be laughing when you're hosted by the ghost of Christmas past You won't be laughing when your blow up doll's got a headache and won't give up the ass And I lay my kicks to rest when I'm impressed So I staple-gun them to my feet This origami dream is beautiful: pull the tail watch the wings flap But you really can't do a thing with that All I ever wanted was to pick apart the day Swallow up the pieces ...
Lyrics: Voice: "Day turns Night" x8 [Aesop Rock] Night Light suckas.. Put one up shackle me, not clean logic procreation I did invent the wheel, in a previous generation While the triple sixers lassos keep angels roped in the basement I locate my old halos and pass em out to the pavement Y'all catch a 30-second flash frame Dirty cooperative Neptune bloom head-trip split Fantastic! Fathom the splicing of major league low lifes With anti hero earthworm mentality (Godzilla!) I paste my game to zero all completion See a cretin's still a cretin even speakin' altered moniker American nightmare lost in the monitor I'll hold the door open so you can stagger through Then ten berserk and bread cookies in after you It's the gutter and I spell it with the 'G' I stole from "Get the fuck up" Noise crutch stolen wretched refuse of my teaming dumb luck Still I promise temperance storm breed still bleeding Amish See the freaks sucked out the wattage while 3 bears invade the cottage And I can't sleep now Yeah, the police'll laugh You won't be laughing when your covered wagons crash You won't be laughing when you're hosted by the ghost of Christmas past You won't be laughing when your blow up doll's got a headache and won't give up the ass And I lay my kicks to rest when I'm impressed So I staple-gun them to my feet This origami dream is beautiful: pull the tail watch the wings flap But you really can't do a thing with that All I ever wanted was to pick apart the day Swallow up the pieces ...
How to replace ear cushions on the Koss UR-20 headphone
How to replace ear cushions on the Koss UR-20 headphone Video Clips. Duration : 7.23 Mins.
In this tutorial I'll be demonstrating how to replace the ear cushions on a pair of Koss headphones, specifically the Koss UR-20. You can buy the cushions themselves directly from Koss. I'll also be detailing how I used a sock to cover the padding over the speaker that the replacement cushions do not cover. Full transcript and show notes at www.thoughtshots.com Related links: Order the replacement cushions from Koss - www.koss.com dleithinger's Sockophones tutorial - www.instructables.com
In this tutorial I'll be demonstrating how to replace the ear cushions on a pair of Koss headphones, specifically the Koss UR-20. You can buy the cushions themselves directly from Koss. I'll also be detailing how I used a sock to cover the padding over the speaker that the replacement cushions do not cover. Full transcript and show notes at www.thoughtshots.com Related links: Order the replacement cushions from Koss - www.koss.com dleithinger's Sockophones tutorial - www.instructables.com
Line output converter installation
Line output converter installation Tube. Duration : 4.32 Mins.
This video describes how I installed a line output converter in my 1984 volkswagen rabbit cabriolet. Since I wanted to keep my stock radio which doesn't support RCA output, I had to install a line out converter (LOC) which would give me the RCA output needed to hook up my kenwood amp. I hope this helps some of you
This video describes how I installed a line output converter in my 1984 volkswagen rabbit cabriolet. Since I wanted to keep my stock radio which doesn't support RCA output, I had to install a line out converter (LOC) which would give me the RCA output needed to hook up my kenwood amp. I hope this helps some of you
Friday, October 19, 2012
0 commentsHow to connect the creative sounblaster X-Fi 5.1 surround sound card
How to connect the creative sounblaster X-Fi 5.1 surround sound card Tube. Duration : 6.13 Mins.
Just a video showing you how to connect the Creative X-Fi sound card
Just a video showing you how to connect the Creative X-Fi sound card
Speakers@Google: Nathan Seidle
Speakers@Google: Nathan Seidle Tube. Duration : 47.63 Mins.
Nathan Seidle, the CEO of SparkFun Electronics visits Google in Mountain View. SparkFun Electronics was founded in 2003 by Nathan Seidle. Its first products were Olimex printed circuit boards. The name 'SparkFun' came about because one of the founders of SparkFun was testing a development board, and sparks flew out; Fun was chosen because the company's self-stated aim is to educate people about electronics. On Jan 7, 2010 SparkFun gave away 0000 worth of merchandise during "SparkFun Free Day", where each customer had a chance to get 0 worth of free items. This popular event lasted 1 hour 44 minutes and 47 seconds.
Nathan Seidle, the CEO of SparkFun Electronics visits Google in Mountain View. SparkFun Electronics was founded in 2003 by Nathan Seidle. Its first products were Olimex printed circuit boards. The name 'SparkFun' came about because one of the founders of SparkFun was testing a development board, and sparks flew out; Fun was chosen because the company's self-stated aim is to educate people about electronics. On Jan 7, 2010 SparkFun gave away 0000 worth of merchandise during "SparkFun Free Day", where each customer had a chance to get 0 worth of free items. This popular event lasted 1 hour 44 minutes and 47 seconds.
How to build a rodin coil part 1
How to build a rodin coil part 1 Video Clips. Duration : 5.67 Mins.
How to build a Rodin coil Part 1. I am using insulated wire, some have said that the original Rodin Coil is made with uninsulated wire though so if you have it available you could try it.
How to build a Rodin coil Part 1. I am using insulated wire, some have said that the original Rodin Coil is made with uninsulated wire though so if you have it available you could try it.
Thursday, October 18, 2012
0 commentsreplacing audio cables on a technics 1210 mk2 part 1
replacing audio cables on a technics 1210 mk2 part 1 Video Clips. Duration : 9.98 Mins.
this is a video showing you how to change the audio cables on a technics 1200 or a 1210 as they are both the same just 1210s are black and 1200 are silver. i have disabled coment and rating on part one if you want to leave coments or rate please do in on part 2 thank you. INFO: depending on the wattage of your soldering iron depends on how long you will have to hold the tip on the conection before the solder melts, for exsample a 10 to 20 watt soldering iron will take longer than say a 25 to 40 watt soldering iron. it doesent really matter weather you use lead or lead free solder but bear in mind that lead free has a higher tin content than leaded solder and contains more flux so its harder to melt also leaded solder is soter but lead free solder is more brittle than lede solder. WARNIGS: make shure you unplug the turntable before unscrewing or opening. be careful not to breake any of the thin wires from the tone arm as they are a very delicate. Never turn the turntable upside down without any type of cushion under underneath it you could damage the tone arm, and be careful if youre using the turntable dust cover to support the turntable whilst its upside down the plastic they are made from is very brittle.
this is a video showing you how to change the audio cables on a technics 1200 or a 1210 as they are both the same just 1210s are black and 1200 are silver. i have disabled coment and rating on part one if you want to leave coments or rate please do in on part 2 thank you. INFO: depending on the wattage of your soldering iron depends on how long you will have to hold the tip on the conection before the solder melts, for exsample a 10 to 20 watt soldering iron will take longer than say a 25 to 40 watt soldering iron. it doesent really matter weather you use lead or lead free solder but bear in mind that lead free has a higher tin content than leaded solder and contains more flux so its harder to melt also leaded solder is soter but lead free solder is more brittle than lede solder. WARNIGS: make shure you unplug the turntable before unscrewing or opening. be careful not to breake any of the thin wires from the tone arm as they are a very delicate. Never turn the turntable upside down without any type of cushion under underneath it you could damage the tone arm, and be careful if youre using the turntable dust cover to support the turntable whilst its upside down the plastic they are made from is very brittle.
How to make a Cat5e Network/Ethernet Cable
How to make a Cat5e Network/Ethernet Cable Video Clips. Duration : 8.82 Mins.
www.cablesupply.com Jim Gibson, from CableSupply.com, shows us how to make a patch cord from scratch. To purchase the needed parts go to http Check out our Facebook page to ask questions and get our informational TechBits! www.facebook.com - Supplies - Mod plugs: cablesupply.com Crimpers: cablesupply.com Cutters: cablesupply.com Follow us on twitter: www.twitter.com This video explains the Cat.5E color code: www.youtube.com How to make a Cat5E cable. Fast Ethernet and Gigabit computer networks require Enhanced Category 5 high-speed cabling to distribute data, voice and video. Enhanced Cat5 350Mhz Snag less Patch Cables are always extremely High quality. These CAT5e cables will handle bandwidth intensive applications up to 350 Mhz and beyond. Each CAT5e cable comes UL verified to meet all Cat 5e cables TIA/EIA standards, and drastically reduce both impedance and structural return loss (SRL) as compared to standard 100 Mhz CAT5 cable. Constructed with high-quality wire and a shortened body plug will keep Near-end Cross talk (NEXT) levels to a minimum. The molded, snag-free boot prevents unwanted cable snags during installation and provides extra strain-relief. Cables4sure 350 MHz Snag less CAT5e patch cables are available in a variety of colors to easily color-code your network installation. -Cat5e cable connector: 50-micron gold plated RJ-45 Male to Male -Cat5e cable conductor: 4-pair 24 AWG Stranded Copper -Cat5e cable jacket: PVC -Molded, Snag-Free boot prevents unwanted ...
www.cablesupply.com Jim Gibson, from CableSupply.com, shows us how to make a patch cord from scratch. To purchase the needed parts go to http Check out our Facebook page to ask questions and get our informational TechBits! www.facebook.com - Supplies - Mod plugs: cablesupply.com Crimpers: cablesupply.com Cutters: cablesupply.com Follow us on twitter: www.twitter.com This video explains the Cat.5E color code: www.youtube.com How to make a Cat5E cable. Fast Ethernet and Gigabit computer networks require Enhanced Category 5 high-speed cabling to distribute data, voice and video. Enhanced Cat5 350Mhz Snag less Patch Cables are always extremely High quality. These CAT5e cables will handle bandwidth intensive applications up to 350 Mhz and beyond. Each CAT5e cable comes UL verified to meet all Cat 5e cables TIA/EIA standards, and drastically reduce both impedance and structural return loss (SRL) as compared to standard 100 Mhz CAT5 cable. Constructed with high-quality wire and a shortened body plug will keep Near-end Cross talk (NEXT) levels to a minimum. The molded, snag-free boot prevents unwanted cable snags during installation and provides extra strain-relief. Cables4sure 350 MHz Snag less CAT5e patch cables are available in a variety of colors to easily color-code your network installation. -Cat5e cable connector: 50-micron gold plated RJ-45 Male to Male -Cat5e cable conductor: 4-pair 24 AWG Stranded Copper -Cat5e cable jacket: PVC -Molded, Snag-Free boot prevents unwanted ...
Wednesday, October 17, 2012
0 comments1971 Chevy Chevelle ON CRAIGSLIST FOR SALE MOHAVE COUNTY AZ
1971 Chevy Chevelle ON CRAIGSLIST FOR SALE MOHAVE COUNTY AZ Video Clips. Duration : 3.15 Mins.
THIS IS is a California 1971 Chevy Chevelle hard top 2 door which has had tens of thousands invested over the last 6 to 8 years,with no short cuts all high quality parts.ON MOHAVE COUNTY CRAIGSLIST 310-418-5163----------19200.00------- .Lets start with the drivetrain which has all been rebuilt with less than 800 miles on it.The 454 stroker motor is bored 30 over to a 492 with 450 to 475 horse power and 600 foot pounds of torque,with roller rockers,roller cam,edlebrock aluminum high performance heads,edlebrock aluminum airgap manifold,edlebrock aluminum water pump,850 Demon double pumper carb,Hooker headers powder coated black,with 2 1/2 exhaust with Flowmasters.The motor also has a 100 amp alternator,aluminum gear reduction starter,Morossey 6 quart oil pan,MSD ignition and wires with 6000 RPM rev limiter.It also has a billit aluminum distributer with a MSD super mag coil.The transmission is a Muncie 4 speed which was also rebuilt and has a Centerforce 500 hp rated clutch.The rear end is a rebuilt 10 bolt posi limited slip with 373 gears.The front end has also been rebuilt with Moog front end parts and has front and rear SS sway bars and all new coil springs.The car also has APR bolts and custom blue beam headlights.The stereo is an Eclipse with 4 speakers from The Original Parts Group over 1000.00.New interior,door panels,carpet ect.The wheels are 17" American Racing Wheels with new Nitto NT 450 Exterme Performance Tires.It also comes with a new 500.00 California Car ...
THIS IS is a California 1971 Chevy Chevelle hard top 2 door which has had tens of thousands invested over the last 6 to 8 years,with no short cuts all high quality parts.ON MOHAVE COUNTY CRAIGSLIST 310-418-5163----------19200.00------- .Lets start with the drivetrain which has all been rebuilt with less than 800 miles on it.The 454 stroker motor is bored 30 over to a 492 with 450 to 475 horse power and 600 foot pounds of torque,with roller rockers,roller cam,edlebrock aluminum high performance heads,edlebrock aluminum airgap manifold,edlebrock aluminum water pump,850 Demon double pumper carb,Hooker headers powder coated black,with 2 1/2 exhaust with Flowmasters.The motor also has a 100 amp alternator,aluminum gear reduction starter,Morossey 6 quart oil pan,MSD ignition and wires with 6000 RPM rev limiter.It also has a billit aluminum distributer with a MSD super mag coil.The transmission is a Muncie 4 speed which was also rebuilt and has a Centerforce 500 hp rated clutch.The rear end is a rebuilt 10 bolt posi limited slip with 373 gears.The front end has also been rebuilt with Moog front end parts and has front and rear SS sway bars and all new coil springs.The car also has APR bolts and custom blue beam headlights.The stereo is an Eclipse with 4 speakers from The Original Parts Group over 1000.00.New interior,door panels,carpet ect.The wheels are 17" American Racing Wheels with new Nitto NT 450 Exterme Performance Tires.It also comes with a new 500.00 California Car ...
Dell Inspiron 6400, E1505, 1501 Disassembly Part 1
Dell Inspiron 6400, E1505, 1501 Disassembly Part 1 Tube. Duration : 7.05 Mins.
Dell Inspiron 6400 Dell Inspiron E1505 Dell Inspiron 1501 Disassembly Guide. Mission: Replace Damage Speakers..
Dell Inspiron 6400 Dell Inspiron E1505 Dell Inspiron 1501 Disassembly Guide. Mission: Replace Damage Speakers..
How to: Install a subwoofer and amplifier in your vehicle - part 1 of 2
How to: Install a subwoofer and amplifier in your vehicle - part 1 of 2 Tube. Duration : 9.45 Mins.
In this video I explain where all the wires go, how the amp works, how to mount the amp and how to run the wires. This video is meant to be a basic guide and you should always do research and read the instructions for the devices you're installing before you attempt to install them. Hope this video helps you with your install. Thanks for watching!
In this video I explain where all the wires go, how the amp works, how to mount the amp and how to run the wires. This video is meant to be a basic guide and you should always do research and read the instructions for the devices you're installing before you attempt to install them. Hope this video helps you with your install. Thanks for watching!
Tuesday, October 16, 2012
0 comments$99 CVS CRAIG CMP738a 7" Wireless Touchscreen Android Tablet Overview
CVS CRAIG CMP738a 7" Wireless Touchscreen Android Tablet Overview Video Clips. Duration : 8.65 Mins.
Craig 7" Widescreen Touchscreen Wireless Tablet from CVS Pharmacy I picked up this tablet from CVS Pharmacy for my son. He wants to play with my droid phone and my iPad so i thought i would check this out so he can play games on it. I initially used it for about a day with the stock 2.1 android firmware but i didnt like the marketplace that was included and it was buggy.. slow to touch as you will see in the video.. So i did some research and found online people were upgrading the firmware to android 2.1. So I did the same thing and now it has the normal Android marketplace and plays games.. etc.. Here is some information about the tablet.. Cost: (minus 25% coupon) = +tax :) Where: CVS Pharmacy. In store only WIRELESS TOUCHSCREEN TABLET CRAIG CMP 738a Operating system: Stock Android - upgraded to 2.1 Specs of the GRAIG CMP 738a Box 7" (17.8cm) Digital Touch Screen (800×480, 16:9) Screen Roughly 6" x 3.5" - Resistive Screen Processor Speed 700MHz Operating System Android version 2.1 4 GB Built-in Flash Memory Built in 256MB DDR-ll RAM Built-in WiFi (802.11 b/g) -Mini HDMI AV -Out- Jack -Mini USB to Connect to Computer -USB Host (Full sized USB Jack) -Micro SD Card Slot (Support Max. 32GB)) Built-in Rechargable Battery (Device can lst up to 6 hours continuous use) Built-in Speaker and Microphone Supports Browser, e-Book Reader, e-Mail, Photos, Maps, Video, You Tube, Facebook, Twitter, Music, Apps, Marketplace, Clock 3.5mm Stero Hephone Jack 3G Ready (For USB ...
Craig 7" Widescreen Touchscreen Wireless Tablet from CVS Pharmacy I picked up this tablet from CVS Pharmacy for my son. He wants to play with my droid phone and my iPad so i thought i would check this out so he can play games on it. I initially used it for about a day with the stock 2.1 android firmware but i didnt like the marketplace that was included and it was buggy.. slow to touch as you will see in the video.. So i did some research and found online people were upgrading the firmware to android 2.1. So I did the same thing and now it has the normal Android marketplace and plays games.. etc.. Here is some information about the tablet.. Cost: (minus 25% coupon) = +tax :) Where: CVS Pharmacy. In store only WIRELESS TOUCHSCREEN TABLET CRAIG CMP 738a Operating system: Stock Android - upgraded to 2.1 Specs of the GRAIG CMP 738a Box 7" (17.8cm) Digital Touch Screen (800×480, 16:9) Screen Roughly 6" x 3.5" - Resistive Screen Processor Speed 700MHz Operating System Android version 2.1 4 GB Built-in Flash Memory Built in 256MB DDR-ll RAM Built-in WiFi (802.11 b/g) -Mini HDMI AV -Out- Jack -Mini USB to Connect to Computer -USB Host (Full sized USB Jack) -Micro SD Card Slot (Support Max. 32GB)) Built-in Rechargable Battery (Device can lst up to 6 hours continuous use) Built-in Speaker and Microphone Supports Browser, e-Book Reader, e-Mail, Photos, Maps, Video, You Tube, Facebook, Twitter, Music, Apps, Marketplace, Clock 3.5mm Stero Hephone Jack 3G Ready (For USB ...
Bring Me The Horizon-Pray For Plagues cover
Bring Me The Horizon-Pray For Plagues cover Video Clips. Duration : 4.42 Mins.
this is me playing pray for plagues by bring me the horizon. i think it turned out alright for one day off playing this song. solo sucked major balls but we that what i get for one take of this song. i know i made mistakes...dude again i was there wen they happened *the notes on the low b string make my bass on my computer speakers rattle because wen i recorded this song i recorded it on separate speakers so i didn't realize the bass was so high so the bass might rattle on your comp speakers. my equipment guitar: spear t 300 (here the link in case ur interested) www.spearguitar.com picks: Dunlop Jazz III strings: DR tight fit 10's amp: line 6 spider III 15 watt means of recording: i sent a headfone wire from my line 6 to my computer so it recorded directly from the amp to computer thnx for watching comment/rate/subscribe
this is me playing pray for plagues by bring me the horizon. i think it turned out alright for one day off playing this song. solo sucked major balls but we that what i get for one take of this song. i know i made mistakes...dude again i was there wen they happened *the notes on the low b string make my bass on my computer speakers rattle because wen i recorded this song i recorded it on separate speakers so i didn't realize the bass was so high so the bass might rattle on your comp speakers. my equipment guitar: spear t 300 (here the link in case ur interested) www.spearguitar.com picks: Dunlop Jazz III strings: DR tight fit 10's amp: line 6 spider III 15 watt means of recording: i sent a headfone wire from my line 6 to my computer so it recorded directly from the amp to computer thnx for watching comment/rate/subscribe
Monday, October 15, 2012
0 commentsTweeter Install
Tweeter Install Tube. Duration : 3.68 Mins.
First time ever installing tweeters....enjoy and let me know what you think
First time ever installing tweeters....enjoy and let me know what you think
Kenwood TR-7400a Trouble shooting
Kenwood TR-7400a Trouble shooting Video Clips. Duration : 4.97 Mins.
Had this radio given to me recently by a good buddy, he made a "Scanner for Radio equipment" swap, but it did not work out well for him, anyways i am here today working on this Kenwood TR-7400a trying restore this radio to working condition, right now there is very little recieve sound thru the speaker!
Had this radio given to me recently by a good buddy, he made a "Scanner for Radio equipment" swap, but it did not work out well for him, anyways i am here today working on this Kenwood TR-7400a trying restore this radio to working condition, right now there is very little recieve sound thru the speaker!
How To Install A Head Unit And Speakers Step By Step
How To Install A Head Unit And Speakers Step By Step Video Clips. Duration : 43.77 Mins.
This video will show you how to install an aftermarket head unit and speakers step by step from start to finish. The vehicle in the video is a 2000 Toyota 4Runner. The techniques and methods in this video will transfer over to any vehicle. If you have any questions please ask. Video Responses are preferred! Hope this video helps you!
This video will show you how to install an aftermarket head unit and speakers step by step from start to finish. The vehicle in the video is a 2000 Toyota 4Runner. The techniques and methods in this video will transfer over to any vehicle. If you have any questions please ask. Video Responses are preferred! Hope this video helps you!
Sunday, October 14, 2012
0 comments2 Sundown Audio SA-8's on a SAZ1500D Roof Flex in HD
2 Sundown Audio SA-8's on a SAZ1500D Roof Flex in HD Video Clips. Duration : 1.27 Mins.
Same box as before with the SAZ1500d wire at 1/2 ohm, making the roof of my 06 silverado Flex. More videos to come with a better box. Sound Solutions Audio forum name "quiet"
Same box as before with the SAZ1500d wire at 1/2 ohm, making the roof of my 06 silverado Flex. More videos to come with a better box. Sound Solutions Audio forum name "quiet"
Elegant Sportbike Motorcycle Speakers
Elegant Sportbike Motorcycle Speakers Video Clips. Duration : 6.40 Mins.
The UniqCycle low-profile motorcycle speaker kit allows me an elegant and semi-hidden installation on my 2005 Ninja ZX-10r. All the other sport bike motorcycle stereo speakers I've seen so far have the speakers exposed or in awkward places. Video shot at Hilton Lagoon, Waikiki, Honolulu, Hawaii. GPS coordinates: 21.281319,-157.840136
The UniqCycle low-profile motorcycle speaker kit allows me an elegant and semi-hidden installation on my 2005 Ninja ZX-10r. All the other sport bike motorcycle stereo speakers I've seen so far have the speakers exposed or in awkward places. Video shot at Hilton Lagoon, Waikiki, Honolulu, Hawaii. GPS coordinates: 21.281319,-157.840136
Saturday, October 13, 2012
0 commentsScion tC broken rear hatch handle panel repair tutorial
Scion tC broken rear hatch handle panel repair tutorial Tube. Duration : 3.93 Mins.
Scion tC's are great little cars. Lots of fun to drive and very popular. Unfortunately, they seem to suffer from a common defect. With enough use, the rear hatch release panel will break off due to the flimsy plastic anchor points beneath the panel that get brittle with age and weakened with use. I've seen several tC's around my own town that have had the panels broken. New, color matched replacement panels are available online as of this posting for 8 plus shipping, but of course, you need to be able to disassemble the handle switch, logo, etc. and re-install on the new panel, which is not only throwing money down the tubes, but time consuming and a hassle. I created this vid as a DIY tutorial if you want to repair it yourself for around and about a half hour to hour of your time. A little more care with future use as described in the vid and the repair should hold indefinitely. One thing I failed to mention in the vid is to be sure that the release switch wire that goes to the handle grip is tucked out of the way before refastening the panel. You don't want to pinch these wires for obvious reasons. Update: In order for the simple repair shown in the video to work, you need to retrain yourself on how to open the rear hatch. If you have a spoiler, simply squeeze the handle release with one hand and use the other up under the spoiler to lift the rear hatch. Otherwise, reach underneath the hatch and lift the panel via the lower lip of the panel (as shown in the vid ...
Scion tC's are great little cars. Lots of fun to drive and very popular. Unfortunately, they seem to suffer from a common defect. With enough use, the rear hatch release panel will break off due to the flimsy plastic anchor points beneath the panel that get brittle with age and weakened with use. I've seen several tC's around my own town that have had the panels broken. New, color matched replacement panels are available online as of this posting for 8 plus shipping, but of course, you need to be able to disassemble the handle switch, logo, etc. and re-install on the new panel, which is not only throwing money down the tubes, but time consuming and a hassle. I created this vid as a DIY tutorial if you want to repair it yourself for around and about a half hour to hour of your time. A little more care with future use as described in the vid and the repair should hold indefinitely. One thing I failed to mention in the vid is to be sure that the release switch wire that goes to the handle grip is tucked out of the way before refastening the panel. You don't want to pinch these wires for obvious reasons. Update: In order for the simple repair shown in the video to work, you need to retrain yourself on how to open the rear hatch. If you have a spoiler, simply squeeze the handle release with one hand and use the other up under the spoiler to lift the rear hatch. Otherwise, reach underneath the hatch and lift the panel via the lower lip of the panel (as shown in the vid ...
Benefits & Results of Subwoofer Coupling (with QSC KW181's)
Benefits & Results of Subwoofer Coupling (with QSC KW181's) Video Clips. Duration : 7.77 Mins.
www.agiprodj.com DJ Rick reviews the benefits and expected results of coupling subwoofers together. Shop with us on the web: www.agiprodj.com Call us toll free: 866-PRO-MIXX or email us: sales AT agiprodj DOT com
www.agiprodj.com DJ Rick reviews the benefits and expected results of coupling subwoofers together. Shop with us on the web: www.agiprodj.com Call us toll free: 866-PRO-MIXX or email us: sales AT agiprodj DOT com
ROCKIN' PAPER PLATE SPEAKER!!
ROCKIN' PAPER PLATE SPEAKER!! Video Clips. Duration : 4.52 Mins.
Make a real working paper plate speaker for under .00! www.thekingofrandom.com To all the MythBusters fans out there .. No offense to MythBusters is intended. I realize they busted the HouseholdHacker project that claimed using aluminum foil and a penny would work. However, I was motivated on this project mainly by the statement that "a paper plate speaker for less than a dollar, really is just too good to be true". This video is meant to be a fun way to show it can be done under . If copper wire is an issue, the TV hacking is to demonstrate that copper wire is everywhere, not just in stores. I hope you like it! WARNING Do not try hacking your TV at home. The capacitors may hold a charge and pose a risk of electric shock. This project should not be attempted without adult supervision and adequate training. Misuse, or careless use, of tools or projects may result in serious injury or death. Use of this video content is at your own risk. Music by www.danosongs.com (Gem Droids) Project inspired by Kipkay/MakeMagazine youtu.be The idea of making a speaker out of a paper plate is intriguing, and to do it for under a buck is even better. But first, we'll have to understand how a speaker works.
Make a real working paper plate speaker for under .00! www.thekingofrandom.com To all the MythBusters fans out there .. No offense to MythBusters is intended. I realize they busted the HouseholdHacker project that claimed using aluminum foil and a penny would work. However, I was motivated on this project mainly by the statement that "a paper plate speaker for less than a dollar, really is just too good to be true". This video is meant to be a fun way to show it can be done under . If copper wire is an issue, the TV hacking is to demonstrate that copper wire is everywhere, not just in stores. I hope you like it! WARNING Do not try hacking your TV at home. The capacitors may hold a charge and pose a risk of electric shock. This project should not be attempted without adult supervision and adequate training. Misuse, or careless use, of tools or projects may result in serious injury or death. Use of this video content is at your own risk. Music by www.danosongs.com (Gem Droids) Project inspired by Kipkay/MakeMagazine youtu.be The idea of making a speaker out of a paper plate is intriguing, and to do it for under a buck is even better. But first, we'll have to understand how a speaker works.
Friday, October 12, 2012
0 commentsInstalling a IFP207 Peugeot 207 dedicated kit
Installing a IFP207 Peugeot 207 dedicated kit Video Clips. Duration : 3.62 Mins.
Integration Focal IFP 207 4-speaker Kit. Dedicated to Peugeot 207. Easy installation in less than 1 hour. The Kit can be installed in Peugeot 307 or 308.
Integration Focal IFP 207 4-speaker Kit. Dedicated to Peugeot 207. Easy installation in less than 1 hour. The Kit can be installed in Peugeot 307 or 308.
VR291-Monster Beats by Dr Dre Tour Earphones w/ Control Talk
VR291-Monster Beats by Dr Dre Tour Earphones w/ Control Talk Tube. Duration : 8.93 Mins.
www.BuyMeAniPhone.com You can purchase these earphones from Monster tinyurl.com Description from BeatsByDre.com: High Resolution Sound Ultra-fast, accurate speaker design delivers the full details of todays digital music with extreme clarity and deep bass Built-in Mic for Hands-Free Calls and Online Chats ControlTalk's built-in mic let's you talk hands-free on your iPhone or music phone. It even works with online voice or video chats on iPhone or iPod touch. Control iPhone and iPod the Easy Way ControlTalk gives you on-cable playback control of your iPhone or iPod, including pause, next track and volume. Full Power Large, high-efficiency drivers let you crank it up and enjoy loud play without sound-wrecking distortion. Monster XLN® High Performance Headphone Cable At Monster, we know cable. Tour ControlTalk's cable features Monsters patented magnetic flux tube and Micro-strand construction to provide clear, no-loss audio and reduced interference. Tangle Free Cable Earbuds are incredibly convenient, but theyve got one big problem: they tangle. But Monsters innovative, patent-pending flat cable design is ultra-flexible and tangle-free. Noise Isolation Sealed in-ear design and multiple eartip designs blocks out external noise so you hear a lot more of the details in your music and a lot less of the outside world. What's In The Box • Headphones with built-in ControlTalk™ • Carrying Case • 3 pairs of standard Monster designed ear-tips • 2 pairs of different sized triple layer ...
www.BuyMeAniPhone.com You can purchase these earphones from Monster tinyurl.com Description from BeatsByDre.com: High Resolution Sound Ultra-fast, accurate speaker design delivers the full details of todays digital music with extreme clarity and deep bass Built-in Mic for Hands-Free Calls and Online Chats ControlTalk's built-in mic let's you talk hands-free on your iPhone or music phone. It even works with online voice or video chats on iPhone or iPod touch. Control iPhone and iPod the Easy Way ControlTalk gives you on-cable playback control of your iPhone or iPod, including pause, next track and volume. Full Power Large, high-efficiency drivers let you crank it up and enjoy loud play without sound-wrecking distortion. Monster XLN® High Performance Headphone Cable At Monster, we know cable. Tour ControlTalk's cable features Monsters patented magnetic flux tube and Micro-strand construction to provide clear, no-loss audio and reduced interference. Tangle Free Cable Earbuds are incredibly convenient, but theyve got one big problem: they tangle. But Monsters innovative, patent-pending flat cable design is ultra-flexible and tangle-free. Noise Isolation Sealed in-ear design and multiple eartip designs blocks out external noise so you hear a lot more of the details in your music and a lot less of the outside world. What's In The Box • Headphones with built-in ControlTalk™ • Carrying Case • 3 pairs of standard Monster designed ear-tips • 2 pairs of different sized triple layer ...
2 12inch mtx 9500' at 1ohm
2 12inch mtx 9500' at 1ohm Tube. Duration : 9.55 Mins.
It's a long video but its worth it they getting pushed down two 1 ohm i have a hifonics brutus amplifier 2600 watts of PURE POWER with zero gauge ground and power wire i have just a factory/stock head unit i will upgrade later on with a double din and add some second skin or dymamat 2 kicker 6x9's 2 kicker 6.5's 1 hifonics 2600 watt brutus amplifier at 1ohm 1 super bass probox for 2 12's 1 zero gauge amp kit
It's a long video but its worth it they getting pushed down two 1 ohm i have a hifonics brutus amplifier 2600 watts of PURE POWER with zero gauge ground and power wire i have just a factory/stock head unit i will upgrade later on with a double din and add some second skin or dymamat 2 kicker 6x9's 2 kicker 6.5's 1 hifonics 2600 watt brutus amplifier at 1ohm 1 super bass probox for 2 12's 1 zero gauge amp kit
Thursday, October 11, 2012
0 commentskicker Wiring Subwoofer 4ohms DVC to 2ohms or 8ohms
kicker Wiring Subwoofer 4ohms DVC to 2ohms or 8ohms Tube. Duration : 3.70 Mins.
alright everybody to wire a dvc 4ohms to a final impedence of 2 ohms you have to first conncect both positive terminals and then both negative terminals then you are going to run a separate wire to one of the positive coils and another wire to a negative coil. dont connect the positive and negative to the same coil it has to be one of each. to wire the dvc 4ohms sub to an impedence of 8ohms you have to connect one positive to one negative, again not of the same voice coil and then your left with a positive and a negative and those are your positive and negative that go to ur amp
alright everybody to wire a dvc 4ohms to a final impedence of 2 ohms you have to first conncect both positive terminals and then both negative terminals then you are going to run a separate wire to one of the positive coils and another wire to a negative coil. dont connect the positive and negative to the same coil it has to be one of each. to wire the dvc 4ohms sub to an impedence of 8ohms you have to connect one positive to one negative, again not of the same voice coil and then your left with a positive and a negative and those are your positive and negative that go to ur amp
Aesop Rock - Daylight lyrics
Aesop Rock - Daylight lyrics Video Clips. Duration : 4.45 Mins.
Aesop rock daylight lyrics : Yes, yes, y'all, and ya don't stop, keep on, to the break of dawn(4x) Yyo... Put one up for shackle-me not clean logic procreation I did not invent the wheel, I was the crooked spoke adjacent While the triple-sixers' lassos keep angels roped in the basement I walk the block with a halo and a stick pokin' your patience. Y'all catch a 30 second flash visual Dirty cooperative med platoon, bloom, head-trip split ridiculous Fathom the splicing of first generation fuck-up with trickle-down anti-hero smack-- Crackin'! I pace me game for zero hour completion greetin' splash Duke of early retirement, pick a dream, American nightmare hoggin' the screen --I'll hold the door open so you can stumble in If you'd stop followin' me 'round the jungle gym. Now it's Honor and I spell it with the HI stole from Heritage Merit crutch stolen wretched refuse of my teaming resonance I promise: temperance towards breed with a leaning conscious See, the creed acts sense responsive, but my sports supports the wattage, and I'm sleeping now! (Wow!) Yeah, the settlers laugh, You won't be laughing when your covered wagons crash! You won't be laughing when the buzzards drag your brother's flags into rags! You won't be laughing when your front lawn is spangled with epitaphs! You won't be laughing! And I'll hang my boots to rest when I'm impressed So I triple knot 'em and forgot 'em. This origami dream is beautiful, but man, those wings'll never leave the ground without a ...
Aesop rock daylight lyrics : Yes, yes, y'all, and ya don't stop, keep on, to the break of dawn(4x) Yyo... Put one up for shackle-me not clean logic procreation I did not invent the wheel, I was the crooked spoke adjacent While the triple-sixers' lassos keep angels roped in the basement I walk the block with a halo and a stick pokin' your patience. Y'all catch a 30 second flash visual Dirty cooperative med platoon, bloom, head-trip split ridiculous Fathom the splicing of first generation fuck-up with trickle-down anti-hero smack-- Crackin'! I pace me game for zero hour completion greetin' splash Duke of early retirement, pick a dream, American nightmare hoggin' the screen --I'll hold the door open so you can stumble in If you'd stop followin' me 'round the jungle gym. Now it's Honor and I spell it with the HI stole from Heritage Merit crutch stolen wretched refuse of my teaming resonance I promise: temperance towards breed with a leaning conscious See, the creed acts sense responsive, but my sports supports the wattage, and I'm sleeping now! (Wow!) Yeah, the settlers laugh, You won't be laughing when your covered wagons crash! You won't be laughing when the buzzards drag your brother's flags into rags! You won't be laughing when your front lawn is spangled with epitaphs! You won't be laughing! And I'll hang my boots to rest when I'm impressed So I triple knot 'em and forgot 'em. This origami dream is beautiful, but man, those wings'll never leave the ground without a ...
Wednesday, October 10, 2012
0 commentsHome made vinyl cutter / incisore fonografico fatto in casa.
Home made vinyl cutter / incisore fonografico fatto in casa. Tube. Duration : 5.83 Mins.
This video shows the setting-up of a simple vinyl cutter. As a music/vinyl lover a real cutter was in my dreams but it was too expensive. This one has been made mainly from "trash" (old loudspeakers, hardware etc.). I used CDs as "blanks". The black ones really resemble a real record! The second part of the movie contains the audio from these "records" played with a portable turntable. I apologise for low video/audio quality (I did it with a cheap camera and audio is taken by camera mic as it is played back by the portable turntable speaker) and for my barking dog. ------------------------- Il video mostra le fasi della costruzione di un semplice incisore di dischi di vinile. Come amante della musica e del vinile ho sempre desiderato un incisore ma non me lo sono mai potuto permettere. Questo è stato fatto essenzialmente con materiale di risulta. Ho usato CD come "lacche vuote"; quelli neri diventano davvero simili ad un disco di vinile! La seconda parte del filmato permette di ascoltare il risultato. Mi scuso per la scarsa qualità video e audio (il tutto è stato ripreso con una macchina fotografica digitale economica; il suono è come vien fuori dall'altoparlante del giradischi portatile) e per l'abbaiare del mio cane in sottofondo.
This video shows the setting-up of a simple vinyl cutter. As a music/vinyl lover a real cutter was in my dreams but it was too expensive. This one has been made mainly from "trash" (old loudspeakers, hardware etc.). I used CDs as "blanks". The black ones really resemble a real record! The second part of the movie contains the audio from these "records" played with a portable turntable. I apologise for low video/audio quality (I did it with a cheap camera and audio is taken by camera mic as it is played back by the portable turntable speaker) and for my barking dog. ------------------------- Il video mostra le fasi della costruzione di un semplice incisore di dischi di vinile. Come amante della musica e del vinile ho sempre desiderato un incisore ma non me lo sono mai potuto permettere. Questo è stato fatto essenzialmente con materiale di risulta. Ho usato CD come "lacche vuote"; quelli neri diventano davvero simili ad un disco di vinile! La seconda parte del filmato permette di ascoltare il risultato. Mi scuso per la scarsa qualità video e audio (il tutto è stato ripreso con una macchina fotografica digitale economica; il suono è come vien fuori dall'altoparlante del giradischi portatile) e per l'abbaiare del mio cane in sottofondo.
WHAT'S INSIDE MY POINT-SOURCE SPEAKERS?
WHAT'S INSIDE MY POINT-SOURCE SPEAKERS? Tube. Duration : 7.32 Mins.
Making cross-overs is really simple stuff, once you get the basic idea. Chokes let only bass into a speaker. Capacitors only let treble into a speaker. The higher the value of the bass choke. the lower the bass. (opposite) (remember)! The higher the value of the treble capacitor, the lower the treble notes that it will let in. (also opposite) (easy to remember)! But you have to also experiment with your control resistors that are in series with the boom chokes and the tizz capacitor. The thump choke (5.6 value) is wired straight in series with the woofer. Then the boom choke (1.0 value) is in parallel with the thump choke. A control resistor (56 ohms) is in series with the boom choke. We don't want much boom in the woofer, most is in the full-range (for point-source sound). But no thump in full-range driver. With the full-range speaker, you have a basic music resistor (56 ohms) feeding all of the signal information but at lower than normal volume. It seems a high value resistor but the add-ons also contain some med and that adds to the basic music resistor. You then add tizz by having a tizz capacitor in parallel (about 3 mf value). And you know what to do if its too chuffy or has too much lower frequency treble (lower the value to 2 mf, as in my case). If it's too thin with too much higher frequency treble (increase to 4.7 mf). The same rule mentioned above! (remember). If it's a small bookshelf speaker, with hardly any bass, put a small resistor in series with the tizz ...
Making cross-overs is really simple stuff, once you get the basic idea. Chokes let only bass into a speaker. Capacitors only let treble into a speaker. The higher the value of the bass choke. the lower the bass. (opposite) (remember)! The higher the value of the treble capacitor, the lower the treble notes that it will let in. (also opposite) (easy to remember)! But you have to also experiment with your control resistors that are in series with the boom chokes and the tizz capacitor. The thump choke (5.6 value) is wired straight in series with the woofer. Then the boom choke (1.0 value) is in parallel with the thump choke. A control resistor (56 ohms) is in series with the boom choke. We don't want much boom in the woofer, most is in the full-range (for point-source sound). But no thump in full-range driver. With the full-range speaker, you have a basic music resistor (56 ohms) feeding all of the signal information but at lower than normal volume. It seems a high value resistor but the add-ons also contain some med and that adds to the basic music resistor. You then add tizz by having a tizz capacitor in parallel (about 3 mf value). And you know what to do if its too chuffy or has too much lower frequency treble (lower the value to 2 mf, as in my case). If it's too thin with too much higher frequency treble (increase to 4.7 mf). The same rule mentioned above! (remember). If it's a small bookshelf speaker, with hardly any bass, put a small resistor in series with the tizz ...
GTA Car Kits - Volkswagen Touareg 2002-2010 install of iPhone, iPod and AUX for factory stereo
GTA Car Kits - Volkswagen Touareg 2002-2010 install of iPhone, iPod and AUX for factory stereo Video Clips. Duration : 8.43 Mins.
www.gtacarkits.com - installation instruction for iPhone, iPod, AUX, mp3 adapter into factory stereo of Volkswagen Touareg for model years 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009 and 2010. After installing the car kit you would be able to listen to your music player or iPhone through your factory stereo speakers and control your music through controls on the factory radio. You also can charge your iPod/iPhone.
www.gtacarkits.com - installation instruction for iPhone, iPod, AUX, mp3 adapter into factory stereo of Volkswagen Touareg for model years 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009 and 2010. After installing the car kit you would be able to listen to your music player or iPhone through your factory stereo speakers and control your music through controls on the factory radio. You also can charge your iPod/iPhone.
Tuesday, October 9, 2012
0 commentsHow to Build a Microphone Lead Using Neutrik XLR's 2011
How to Build a Microphone Lead Using Neutrik XLR's 2011 Video Clips. Duration : 5.30 Mins.
After much demand we have finally made a new video guide on how to build a mic lead using Neutrik XLR's We also demonstrate the use of Heat-Shrinks and how they can be branded with logos and information. Pro Audio Stash has it's very own professional cable building department designed specifically for providing customers with bespoke cables and leads. We can custom build Speaker leads, Power leads, Microphone leads, Instrument leads, XLR Looms & Mulit-Core Cable. Heat-Shrink service is also available which enables you to have your cables branded or ID with any logo or text in a number of different colours, styles and fonts. We only use Neutrik connectors and cable from either Kelsey or Proel to enusre that only the best quality products are used. All our custom cables come with a LIFE TIME WARRANTY. Please call a member of our sales team to get an instant quote today call - 01424 429641 or visit the website: www.proaudiostash.co.uk
After much demand we have finally made a new video guide on how to build a mic lead using Neutrik XLR's We also demonstrate the use of Heat-Shrinks and how they can be branded with logos and information. Pro Audio Stash has it's very own professional cable building department designed specifically for providing customers with bespoke cables and leads. We can custom build Speaker leads, Power leads, Microphone leads, Instrument leads, XLR Looms & Mulit-Core Cable. Heat-Shrink service is also available which enables you to have your cables branded or ID with any logo or text in a number of different colours, styles and fonts. We only use Neutrik connectors and cable from either Kelsey or Proel to enusre that only the best quality products are used. All our custom cables come with a LIFE TIME WARRANTY. Please call a member of our sales team to get an instant quote today call - 01424 429641 or visit the website: www.proaudiostash.co.uk
How To Build A Subwoofer Box | Beginner Car Audio Tutorial - Dual 12" Custom Ported Sub Enclosure
How To Build A Subwoofer Box | Beginner Car Audio Tutorial - Dual 12" Custom Ported Sub Enclosure Video Clips. Duration : 6.37 Mins.
Ever wanted to build yourself a nice subwoofer box, but don't know how to design, build or install one? Look no further! These series of videos will show you all the steps to making your very own custom box! Thumbs Up For More Videos & Thanks For Watching :) Thanks For Rating & Subscribing! www.youtube.com Video Installing Rob's Stereo www.youtube.com Music By: T-Mic Beats Songs: "Hit me Up" "Bang Bang" "Exotic Nerotic" www.tmicbeats.com www.youtube.com DIY Direction : Step One: Designing The Enclosure For Your Musical Needs - Tune & Tinker (What type of music do you listen to? Rap? Country? Do you like deep sounding bass? Or do you like punchy high bass? Answer yourself these questions before deciding on a 32hz tuning frequency) - We will use the RE Box Calculator to get our box dimensions & cut measurements for this project Step Two: Buying The Supplies - We will bring you inside the store showing what to buy for the best / loudest results for your homemade box Tools & Supplies Needed: 2 Sheets Of 3/4" MDF Wood (2 Layers Thick) Liquid Nails High Grade Construction Adhesive Single Gallon of Fiberglass Resin Bondo Short Strand Fiberglass 80 & 220 Grit Sandpaper 1.25" & 2.5" Brad Nail Sets 2.5" Deck Screws Titebond Wood Glue (Red / Blue Type) Killz Original Primer (Awesome Stuff) Paint Of Yuor Choosing Step Three : Marking & Making The Cuts - We will demonstrate how all the cutting can be made with a simple skill saw. Step Four : Watchu crazy ? LOL That's For Next Time ...
Ever wanted to build yourself a nice subwoofer box, but don't know how to design, build or install one? Look no further! These series of videos will show you all the steps to making your very own custom box! Thumbs Up For More Videos & Thanks For Watching :) Thanks For Rating & Subscribing! www.youtube.com Video Installing Rob's Stereo www.youtube.com Music By: T-Mic Beats Songs: "Hit me Up" "Bang Bang" "Exotic Nerotic" www.tmicbeats.com www.youtube.com DIY Direction : Step One: Designing The Enclosure For Your Musical Needs - Tune & Tinker (What type of music do you listen to? Rap? Country? Do you like deep sounding bass? Or do you like punchy high bass? Answer yourself these questions before deciding on a 32hz tuning frequency) - We will use the RE Box Calculator to get our box dimensions & cut measurements for this project Step Two: Buying The Supplies - We will bring you inside the store showing what to buy for the best / loudest results for your homemade box Tools & Supplies Needed: 2 Sheets Of 3/4" MDF Wood (2 Layers Thick) Liquid Nails High Grade Construction Adhesive Single Gallon of Fiberglass Resin Bondo Short Strand Fiberglass 80 & 220 Grit Sandpaper 1.25" & 2.5" Brad Nail Sets 2.5" Deck Screws Titebond Wood Glue (Red / Blue Type) Killz Original Primer (Awesome Stuff) Paint Of Yuor Choosing Step Three : Marking & Making The Cuts - We will demonstrate how all the cutting can be made with a simple skill saw. Step Four : Watchu crazy ? LOL That's For Next Time ...
Monday, October 8, 2012
0 commentsHow to hotwire a motorcycle
How to hotwire a motorcycle Video Clips. Duration : 1.35 Mins.
This video demonstrates the ridiculously easy process of hotwiring a motorcycle.
This video demonstrates the ridiculously easy process of hotwiring a motorcycle.
Review: Turtle Beach XL1 XBOX 360 headset
Review: Turtle Beach XL1 XBOX 360 headset Video Clips. Duration : 7.28 Mins.
The Turtle Beach XL1 XBOX 360 headset is the perfect entry-level headset for gamers. With crystal-clear sound and communication. The Turtle Beach XL1 features an in-line amplifier providing amplifier audio as well as, providing quick access to independent game and chat volume controls and a built-in fixed bass boost feature that adds depth and realism to the game audio. Features: USB Powered 50mm speakers oversized ear cup Cable length: 16 ft Overall a really good entry-level headset and one i recommend This Review Was Done For: Best Buy UK, TechXperts: www.bestbuy.co.uk Youtube Channel: youtube.com Follow us: Site/Blog: www.geekstech.co.uk Twitter twitter.com Facebook: facebook.com Youtube: www.youtube.com EmpireAvenue: www.empireavenue.com Blip.tv: www.blip.tv Podcast: podcast.geekstech.co.uk
The Turtle Beach XL1 XBOX 360 headset is the perfect entry-level headset for gamers. With crystal-clear sound and communication. The Turtle Beach XL1 features an in-line amplifier providing amplifier audio as well as, providing quick access to independent game and chat volume controls and a built-in fixed bass boost feature that adds depth and realism to the game audio. Features: USB Powered 50mm speakers oversized ear cup Cable length: 16 ft Overall a really good entry-level headset and one i recommend This Review Was Done For: Best Buy UK, TechXperts: www.bestbuy.co.uk Youtube Channel: youtube.com Follow us: Site/Blog: www.geekstech.co.uk Twitter twitter.com Facebook: facebook.com Youtube: www.youtube.com EmpireAvenue: www.empireavenue.com Blip.tv: www.blip.tv Podcast: podcast.geekstech.co.uk
Car Audio Speaker Install w/ Soundstream Picasso 5.25" 2-way Stereo Speakers - EXO SPL System How To
Car Audio Speaker Install w/ Soundstream Picasso 5.25" 2-way Stereo Speakers - EXO SPL System How To Video Clips. Duration : 4.02 Mins.
Had The Strangest Dream The Other Day... Or Was It...? www.youtube.com Enjoy The Music? Subscribe For More ORIGINAL Tracks! "Bumble Bee" - By Cultivata Beats Beat Made On FL Studio 8 www.youtube.com Intro & Ourto Music By: Kevin Macleod incompetech.com Licensed under Creative Commons "Attribution 3.0" creativecommons.org Subscribe For More Videos www.youtube.com The Hook Up
Had The Strangest Dream The Other Day... Or Was It...? www.youtube.com Enjoy The Music? Subscribe For More ORIGINAL Tracks! "Bumble Bee" - By Cultivata Beats Beat Made On FL Studio 8 www.youtube.com Intro & Ourto Music By: Kevin Macleod incompetech.com Licensed under Creative Commons "Attribution 3.0" creativecommons.org Subscribe For More Videos www.youtube.com The Hook Up
Sunday, October 7, 2012
0 commentsApril Wind 11 Abha Torus First Resonance Tests
April Wind 11 Abha Torus First Resonance Tests Tube. Duration : 2.47 Mins.
Finished the 11" diameter 18x36 Abha Torus. It is a plastic slinky covered with duct tape to form the torus, wound CCW with #22 gauge magnet wire. Total of 12 wires, 12 turns per wire for a total of 144 turns. First tests shown here with a 1 inch diameter neoball spinner and Hall sensor, hooked to my 2 transistor pulse circuit. This demo shows the power resonances between the coil and the neoball after the power is turned off. Many different coils show this resonance but it seems more pronounced with the Rodin type coils. Thanks to Randy Powell for discovering the new Abha coil winding geometries such as this one called an 18x36. I plan to try various frequencies now that I finally have a 2-channel signal generator! Go to Google "Rodin Coil" group for more info, and circuit diagram. See also Randy's Youtube videos under the name "theabhakingdom" for understanding the vortex math and the mappings to the torus. checkout vortexspace.org site very good things Aloha
Finished the 11" diameter 18x36 Abha Torus. It is a plastic slinky covered with duct tape to form the torus, wound CCW with #22 gauge magnet wire. Total of 12 wires, 12 turns per wire for a total of 144 turns. First tests shown here with a 1 inch diameter neoball spinner and Hall sensor, hooked to my 2 transistor pulse circuit. This demo shows the power resonances between the coil and the neoball after the power is turned off. Many different coils show this resonance but it seems more pronounced with the Rodin type coils. Thanks to Randy Powell for discovering the new Abha coil winding geometries such as this one called an 18x36. I plan to try various frequencies now that I finally have a 2-channel signal generator! Go to Google "Rodin Coil" group for more info, and circuit diagram. See also Randy's Youtube videos under the name "theabhakingdom" for understanding the vortex math and the mappings to the torus. checkout vortexspace.org site very good things Aloha
Wireless Audio Throughout Your House!
Wireless Audio Throughout Your House! Video Clips. Duration : 7.10 Mins.
Get wireless audio anywhere you want, learn how to run wires through walls when you need to, and my thoughts on the LG Revolution 4G phone. Sonos Play:5 geekbeat.tv/sonosplay5 Wire Installation geekbeat.tv/diywireinstall LG Revolution geekbeat.tv/lgrevolution
Get wireless audio anywhere you want, learn how to run wires through walls when you need to, and my thoughts on the LG Revolution 4G phone. Sonos Play:5 geekbeat.tv/sonosplay5 Wire Installation geekbeat.tv/diywireinstall LG Revolution geekbeat.tv/lgrevolution
Saturday, October 6, 2012
0 commentsHow to: Hook car amp in home (battery)
How to: Hook car amp in home (battery) Video Clips. Duration : 3.68 Mins.
This is the complete how to. Its just basically all parallel wiring. Nothing else. Made for dylan but there might be other's out there that need this help. So here you go. Enjoy. =D
This is the complete how to. Its just basically all parallel wiring. Nothing else. Made for dylan but there might be other's out there that need this help. So here you go. Enjoy. =D
Crazy Subwoofer Skills w/ Thorshammer1488's 2 10" DC Subs - "GORILLA" Flex Recone Bass Demo
Crazy Subwoofer Skills w/ Thorshammer1488's 2 10" DC Subs - "GORILLA" Flex Recone Bass Demo Video Clips. Duration : 2.85 Mins.
Special Guest: Thorshammer1488 This Guy has Some Serious Skills! Watch For Yourself! Thor's Channel www.youtube.com TNESPL www.teamnortheastspl.com
Special Guest: Thorshammer1488 This Guy has Some Serious Skills! Watch For Yourself! Thor's Channel www.youtube.com TNESPL www.teamnortheastspl.com
2010 F-150 Amplifier Installation Part Two
2010 F-150 Amplifier Installation Part Two Video Clips. Duration : 14.45 Mins.
Part two of my installation. Shows How to wire the Metra BT-5520 to add an amplifier to your stock stereo. Also shows the route taken for running speaker wires, and some tips for your installation. Thanks! Also check out my other videos for how to remove the Head Unit if you couldn't figure it out. The video was too long so I made a separate video for that. Materials Used: Panel Removal Kit Metra BT-5520 Wiring Harness Kicker ZX700.5 5 Channel Amplifier Kicker CK44 4-Channel Amp Install Kit (2x) Kicker ZISL (09ZISL) (Speaker Wire to RCA Conversion) Kicker ZXRC (10ZXRC) (Bass Remote Control) Single Subwoofer Box from SupercrewSound.com Alpine SWS-1043D Type-S Subwoofer 300w DVC @4ohms (4x) Infinity Kappa 682.9CF Door Speakers (6x9's) (100w @ 2ohms) **I used a roll of solder to fish the speaker wires through the side panels. I'm sure a coat hanger would work, but solder is more flexible and wont damage anything like a coat hanger might. **As noted in the video, if you used the same amplifier wiring kit, be aware that this kit comes with *barely enough* speaker wire to run through a supercrew. So don't leave a lot of slack on the ends as you will run out of wire. Any questions, leave in the comment section below. Thanks for watching!
Part two of my installation. Shows How to wire the Metra BT-5520 to add an amplifier to your stock stereo. Also shows the route taken for running speaker wires, and some tips for your installation. Thanks! Also check out my other videos for how to remove the Head Unit if you couldn't figure it out. The video was too long so I made a separate video for that. Materials Used: Panel Removal Kit Metra BT-5520 Wiring Harness Kicker ZX700.5 5 Channel Amplifier Kicker CK44 4-Channel Amp Install Kit (2x) Kicker ZISL (09ZISL) (Speaker Wire to RCA Conversion) Kicker ZXRC (10ZXRC) (Bass Remote Control) Single Subwoofer Box from SupercrewSound.com Alpine SWS-1043D Type-S Subwoofer 300w DVC @4ohms (4x) Infinity Kappa 682.9CF Door Speakers (6x9's) (100w @ 2ohms) **I used a roll of solder to fish the speaker wires through the side panels. I'm sure a coat hanger would work, but solder is more flexible and wont damage anything like a coat hanger might. **As noted in the video, if you used the same amplifier wiring kit, be aware that this kit comes with *barely enough* speaker wire to run through a supercrew. So don't leave a lot of slack on the ends as you will run out of wire. Any questions, leave in the comment section below. Thanks for watching!
Friday, October 5, 2012
0 commentsMy New RCA RTB1023 Blu-Ray Home Theater System
My New RCA RTB1023 Blu-Ray Home Theater System Tube. Duration : 6.10 Mins.
Copyright Disclaimer Under Section 107 of the Copyright Act 1976, allowance is made for fair use for purposes such as criticism, comment, news reporting, teaching, scholarship, and research. Fair use is a use permitted by copyright statute that might otherwise be infringing. Non-profit, educational or personal use tips the balance in favor of fair use. Yep I bought me a sound system for my room. This is a lot like the one in my living room (which is also by RCA) this one has a built in Blu-Ray player and surround sound speakers. Only thing is there is no optical port for audio. So you use the old white and red composite audio cables to get the sound from the tv. It's a great 8 investment though and I'm really enjoying all the booming Boogerific sounds! -Booger
Copyright Disclaimer Under Section 107 of the Copyright Act 1976, allowance is made for fair use for purposes such as criticism, comment, news reporting, teaching, scholarship, and research. Fair use is a use permitted by copyright statute that might otherwise be infringing. Non-profit, educational or personal use tips the balance in favor of fair use. Yep I bought me a sound system for my room. This is a lot like the one in my living room (which is also by RCA) this one has a built in Blu-Ray player and surround sound speakers. Only thing is there is no optical port for audio. So you use the old white and red composite audio cables to get the sound from the tv. It's a great 8 investment though and I'm really enjoying all the booming Boogerific sounds! -Booger
How To Hook Up A Headunit / Cd Player / Civic Project
How To Hook Up A Headunit / Cd Player / Civic Project Tube. Duration : 9.40 Mins.
Well I had to re hookup a headunit for my civic hatchback so of course I had to make a video to show people how to hook one up. This video show how to hook up a wiring harness and explains the colors and other things.
Well I had to re hookup a headunit for my civic hatchback so of course I had to make a video to show people how to hook one up. This video show how to hook up a wiring harness and explains the colors and other things.
Lionel Lionmaster UP 4006 Big Boy with Legacy
Lionel Lionmaster UP 4006 Big Boy with Legacy Tube. Duration : 5.50 Mins.
After adjusting the sound commander board, wires, and speaker arrangement in the Polar Express tender, I thought I would give my Lionel Lionmaster UP Big Boy 4006 with legacy a spin around the layout on the outer O48 main line. You can see the start of a new tunnel on one end. Also the Polar Express whistle is now louder than before since more of the air can escape from the tender. I did some low speed passes with the Big boy, medium and high ball so you can experience how it looks and sounds. Sorry I didn't have the smoke unit turned on, that's pretty cool too. In this video, I'm pulling traditional post war cars I had on hand, but normally I use scale Atlas boxcars and scale MTH hoppers, and an scale MTH or Kline caboose.
After adjusting the sound commander board, wires, and speaker arrangement in the Polar Express tender, I thought I would give my Lionel Lionmaster UP Big Boy 4006 with legacy a spin around the layout on the outer O48 main line. You can see the start of a new tunnel on one end. Also the Polar Express whistle is now louder than before since more of the air can escape from the tender. I did some low speed passes with the Big boy, medium and high ball so you can experience how it looks and sounds. Sorry I didn't have the smoke unit turned on, that's pretty cool too. In this video, I'm pulling traditional post war cars I had on hand, but normally I use scale Atlas boxcars and scale MTH hoppers, and an scale MTH or Kline caboose.
Thursday, October 4, 2012
0 commentsFOR SALE : 1968 Mustang Fastback Video 1 of 2
FOR SALE : 1968 Mustang Fastback Video 1 of 2 Tube. Duration : 3.47 Mins.
1968 Fastback Mustang J code, when new came with: 4 speed wide ratio transmission, Power disc brakes, and tachometer. VIN 8F02J158024 , TAG 63A A 2U 13B 41 E 5. Originally Raven Black....look at the Marti report, In 1968 42582 Fastbacks were made.....only (77) of these came with this paint/inter. combination! Prior to the rebuilding of the Mustang , it was found in a barn where it has been stored for the last 30 years, the old license plates have 1981 registration tags Mustang currently has a late model 1990's 5.0 Roller 302 motor with a E303 cam, MSD distributor, MSD coil and MSD 6200 box, Full length headers, Demon carb, Ford racing ignition wires, Cobra style valve covers and oval air cleaner. Late model Mustang T-5 5 speed transmission recently rebuilt, newer clutch, Hi Performance aluminum driveshaft, 9" 3.50 posi rear end. Alum. Radiator (made to look like a stock radiator); Custom 2 ½" exhaust with Flowmaster mufflers, with Flowmaster exhaust tips. New KYB shocks, new coil springs, new reverse eye leaf springs (lowers rear 1"), new front end steering components. 1 1/8" front sway bar , 5/8" rear sway bar, New power brake booster, factory front disc brakes, and rear drum brakes. To keep an era correct look, a stock 4 speed shifter was fabricated to work with this T5 transmission . Car was painted Ford highland green metalic approx 5 months ago, it is nor concourse show quality, but looks good. No bondo anywhere!! Floorpans and bottom of car looks perfect!!! New ...
1968 Fastback Mustang J code, when new came with: 4 speed wide ratio transmission, Power disc brakes, and tachometer. VIN 8F02J158024 , TAG 63A A 2U 13B 41 E 5. Originally Raven Black....look at the Marti report, In 1968 42582 Fastbacks were made.....only (77) of these came with this paint/inter. combination! Prior to the rebuilding of the Mustang , it was found in a barn where it has been stored for the last 30 years, the old license plates have 1981 registration tags Mustang currently has a late model 1990's 5.0 Roller 302 motor with a E303 cam, MSD distributor, MSD coil and MSD 6200 box, Full length headers, Demon carb, Ford racing ignition wires, Cobra style valve covers and oval air cleaner. Late model Mustang T-5 5 speed transmission recently rebuilt, newer clutch, Hi Performance aluminum driveshaft, 9" 3.50 posi rear end. Alum. Radiator (made to look like a stock radiator); Custom 2 ½" exhaust with Flowmaster mufflers, with Flowmaster exhaust tips. New KYB shocks, new coil springs, new reverse eye leaf springs (lowers rear 1"), new front end steering components. 1 1/8" front sway bar , 5/8" rear sway bar, New power brake booster, factory front disc brakes, and rear drum brakes. To keep an era correct look, a stock 4 speed shifter was fabricated to work with this T5 transmission . Car was painted Ford highland green metalic approx 5 months ago, it is nor concourse show quality, but looks good. No bondo anywhere!! Floorpans and bottom of car looks perfect!!! New ...
Choosing a Sound Bar
Choosing a Sound Bar Tube. Duration : 3.10 Mins.
www.crutchfield.com Get the scoop on choosing a soundbar. Soundbars provide a great unobtrusive way to get good sound from your TV. They're a great choice for spaces where there's no room for speakers, or you don't want wires running along the floor.
www.crutchfield.com Get the scoop on choosing a soundbar. Soundbars provide a great unobtrusive way to get good sound from your TV. They're a great choice for spaces where there's no room for speakers, or you don't want wires running along the floor.
Monster Beats By Dre BeatBox Review
Monster Beats By Dre BeatBox Review Tube. Duration : 3.18 Mins.
A review of the BeatsbyDre BeatBox Speakers. All I can really say is that they sound awesome :). Remember to Comment, thumbs up and subscribe! Twitter: twitter.com Website: www.tekbeattv.com Manufacturer Link www.beatsbydre.com
A review of the BeatsbyDre BeatBox Speakers. All I can really say is that they sound awesome :). Remember to Comment, thumbs up and subscribe! Twitter: twitter.com Website: www.tekbeattv.com Manufacturer Link www.beatsbydre.com
Wednesday, October 3, 2012
0 commentsHow to wire 2 dual 2ohm subs to 2 ohm for amplifier
How to wire 2 dual 2ohm subs to 2 ohm for amplifier Video Clips. Duration : 5.57 Mins.
www.defiantaudiollc.com How to wire 2 dual 2ohm subs to 2 ohm for amplifier, Defiant Audio, Elliot Hernandez, How to video for car audio subwoofers
www.defiantaudiollc.com How to wire 2 dual 2ohm subs to 2 ohm for amplifier, Defiant Audio, Elliot Hernandez, How to video for car audio subwoofers
HD 700
HD 700 Video Clips. Duration : 1.13 Mins.
Bring excitement to the next stage of intensity with the new HD 700. Incorporating Sennheiser's signature sound expertise, these open, circumaural dynamic stereo headphones promises outstanding soundstage with a warm and balanced audio reproduction. Paired with specially-tuned, highly efficient drivers capable of delivering high sound pressure levels, immense audio enjoyment is available at your fingertips. Equaling the audio performance are the finest parts expressly selected for production -- highly aesthetic dual-material yoke, angled acoustic baffle, detachable symmetrical silver-plated oxygen-free four-wire copper cable -- for an optimal sound experience. In addition, exceedingly optimized ventilated magnet system minimizes air turbulence and harmonic, intermodulation distortion while a very low THD is achieved by the superior, extremely stable internal damping element. The open-back ear cup design is not only revolutionary but also, to facilitate transparent sound. Extraordinary wearing comfort is ensured, with their ultra comfortable and luxurious earpads, together with its silicone-treated headband resulting in minimal headband resonance. All in all, the HD 700 invites the user to bask in true musical enjoyment. For more informations check www.sennheiser.com
Bring excitement to the next stage of intensity with the new HD 700. Incorporating Sennheiser's signature sound expertise, these open, circumaural dynamic stereo headphones promises outstanding soundstage with a warm and balanced audio reproduction. Paired with specially-tuned, highly efficient drivers capable of delivering high sound pressure levels, immense audio enjoyment is available at your fingertips. Equaling the audio performance are the finest parts expressly selected for production -- highly aesthetic dual-material yoke, angled acoustic baffle, detachable symmetrical silver-plated oxygen-free four-wire copper cable -- for an optimal sound experience. In addition, exceedingly optimized ventilated magnet system minimizes air turbulence and harmonic, intermodulation distortion while a very low THD is achieved by the superior, extremely stable internal damping element. The open-back ear cup design is not only revolutionary but also, to facilitate transparent sound. Extraordinary wearing comfort is ensured, with their ultra comfortable and luxurious earpads, together with its silicone-treated headband resulting in minimal headband resonance. All in all, the HD 700 invites the user to bask in true musical enjoyment. For more informations check www.sennheiser.com
Tuesday, October 2, 2012
0 commentsGTA Car Kits - Honda Accord 2003-2007 install of iPhone, Ipod and AUX adapter for factory stereo
GTA Car Kits - Honda Accord 2003-2007 install of iPhone, Ipod and AUX adapter for factory stereo Video Clips. Duration : 9.68 Mins.
www.gtacarkits.com - installation instruction for iPhone, iPod, AUX, mp3 adapter into factory stereo of Honda Accord for model years 2003, 2004 2005, 2006 and 2007. After installing the car kit you would be able to listen to your music player or iPhone through your factory stereo speakers and control your music through controls on the factory radio. You also can charge your iPod/iPhone.
www.gtacarkits.com - installation instruction for iPhone, iPod, AUX, mp3 adapter into factory stereo of Honda Accord for model years 2003, 2004 2005, 2006 and 2007. After installing the car kit you would be able to listen to your music player or iPhone through your factory stereo speakers and control your music through controls on the factory radio. You also can charge your iPod/iPhone.
rockford fosgate p3 12" subs pt. 2
rockford fosgate p3 12" subs pt. 2 Tube. Duration : 4.00 Mins.
LINK TO THE NEWEST SYSTEM BUILD VIDEO(23 July 2011) www.youtube.com here it is!!!!! i finally finished installing my subs, amp, capacitor, and yellowtop. It is running at 1 ohms and my voltage reads about 13.8-14.2 constantly. so each sub is getting around 625 rms each. system specs: 1 rockford fosgate t-1000-1bd amp wired to 1 ohms 2 rockford fosgate p3 12" subwoofers in a sealed box with their own chambers approx 1 cu. ft for each sub 1 rockford fosgate 1 farad digital hybrid capacitor 1 optima yellowtop battery installed under hood with 4 guage wiring. NO BIG 3. kenwood eXcelon headunit putting out 22 watts rms*4 to 4 2 way kicker speakers. thanks and leave comments on what u think. peace out!
LINK TO THE NEWEST SYSTEM BUILD VIDEO(23 July 2011) www.youtube.com here it is!!!!! i finally finished installing my subs, amp, capacitor, and yellowtop. It is running at 1 ohms and my voltage reads about 13.8-14.2 constantly. so each sub is getting around 625 rms each. system specs: 1 rockford fosgate t-1000-1bd amp wired to 1 ohms 2 rockford fosgate p3 12" subwoofers in a sealed box with their own chambers approx 1 cu. ft for each sub 1 rockford fosgate 1 farad digital hybrid capacitor 1 optima yellowtop battery installed under hood with 4 guage wiring. NO BIG 3. kenwood eXcelon headunit putting out 22 watts rms*4 to 4 2 way kicker speakers. thanks and leave comments on what u think. peace out!
homemade windturbine rotor
homemade windturbine rotor Video Clips. Duration : 4.70 Mins.
simple and easy how to make windturbine rotor,my generator has 8 poles,magnets 20mm+20mm neodmium,stator is from old washingmachine motor,rewound with 1mm cooper wire,25 turns each coil
simple and easy how to make windturbine rotor,my generator has 8 poles,magnets 20mm+20mm neodmium,stator is from old washingmachine motor,rewound with 1mm cooper wire,25 turns each coil
Monday, October 1, 2012
0 commentsHow to repair iphone 3GS/3G Number 3 FPC connector (replacement)
How to repair iphone 3GS/3G Number 3 FPC connector (replacement) Video Clips. Duration : 5.55 Mins.
In this video I am showing you how to repair the number 3 connector, FPC connector for the ear, proximity and light sensor. I sell these connectors on ebay, the item number is 110675174536. If you need me to do the repair for you please send me a message. Thank you!
In this video I am showing you how to repair the number 3 connector, FPC connector for the ear, proximity and light sensor. I sell these connectors on ebay, the item number is 110675174536. If you need me to do the repair for you please send me a message. Thank you!
New Reference Speaker Line from Klipsch
New Reference Speaker Line from Klipsch Video Clips. Duration : 1.52 Mins.
Now in its fifth generation, Reference II speakers boast enhanced features, including re-engineered drivers and a new crossover system, to capture your attention and excite your emotions. In addition to the improved sound quality, the look of "big sound" has been redefined throughout the line with sophisticated cabinetry, refreshed logos and rounded feet.
Now in its fifth generation, Reference II speakers boast enhanced features, including re-engineered drivers and a new crossover system, to capture your attention and excite your emotions. In addition to the improved sound quality, the look of "big sound" has been redefined throughout the line with sophisticated cabinetry, refreshed logos and rounded feet.
Subscribe to:
Posts (Atom)