Monoprice cable fishing video tutorial using our mounting brackets; http://bit.ly/gE40wZ If you have any question about this video, please feel free to conta...
Showing posts with label through. Show all posts
Showing posts with label through. Show all posts
Thursday, May 23, 2013
0 commentsHow to fish cables through the wall
How to fish cables through the wall Tube. Duration : 4.78 Mins.
Monoprice cable fishing video tutorial using our mounting brackets; http://bit.ly/gE40wZ If you have any question about this video, please feel free to conta...
Monoprice cable fishing video tutorial using our mounting brackets; http://bit.ly/gE40wZ If you have any question about this video, please feel free to conta...
Monday, May 6, 2013
0 commentsAudio/Video Installation : How to Run Speaker Wire Through Walls
Audio/Video Installation : How to Run Speaker Wire Through Walls Tube. Duration : 2.18 Mins.
In order to run speaker wire through the walls, an individual will need a low-voltage jack and a cover plate, in addition to speaker wire. Run wire down thro...
In order to run speaker wire through the walls, an individual will need a low-voltage jack and a cover plate, in addition to speaker wire. Run wire down thro...
Tuesday, April 9, 2013
0 commentsROUTING A SPEAKER WIRE THROUGH A FACTORY DOOR BOOT PROPERLY
ROUTING A SPEAKER WIRE THROUGH A FACTORY DOOR BOOT PROPERLY Video Clips. Duration : 1.42 Mins.
THIS VIDEO SIMPLY SHOWS A METHOD OF ROUTING A SPEAKER WIRE FROM THE FACTORY DOOR LOCATION THROUGH THE BOOT . THAT WAY IT DOESNT LOOK ALL CRAZY ON THE OUTSIDE...
THIS VIDEO SIMPLY SHOWS A METHOD OF ROUTING A SPEAKER WIRE FROM THE FACTORY DOOR LOCATION THROUGH THE BOOT . THAT WAY IT DOESNT LOOK ALL CRAZY ON THE OUTSIDE...
Sunday, February 17, 2013
0 commentsHow To Get Rid of Engine Whining/Noise through speakers
How To Get Rid of Engine Whining/Noise through speakers Video Clips. Duration : 1.85 Mins.
This had been a problem for over a year with my subwoofers and I just learned to get over it because it was only audible when the volume was down, and it wasn't too loud. But then I was installing my mids/highs amp and the sound was AWFUL! Don't ask how I found this out haha but I'm so happy I did. Finally everything's quiet when the volume is down :) Good luck!
This had been a problem for over a year with my subwoofers and I just learned to get over it because it was only audible when the volume was down, and it wasn't too loud. But then I was installing my mids/highs amp and the sound was AWFUL! Don't ask how I found this out haha but I'm so happy I did. Finally everything's quiet when the volume is down :) Good luck!
Monday, October 29, 2012
0 commentsWireless electricity transfer through electric resonance
Wireless electricity transfer through electric resonance Tube. Duration : 2.00 Mins.
-Input Signal: 188 KHz, square wave AC, 20 Volts Peak to Peak (Vpp) or 10 Volts Root Main Square (RMS) from a Signal Generator -Capacitors: Unpolarized, in parallel with coil (not mandatory to have capacitor at the transmitter, but increases slightly led brightness) -Coils: length=5 meters, diameter=1 mm, single wire, single layer, cylinder diameter= 12 cm, speaker cable for both transmitter & receiver (coil shape matters !!!) -LED: 1 bright 3Volt white LED at the receiver coil -Resonance occurs at more frequencies: 16, 20, 26, 36, 59, 188 KHZ (led is brightest at 188 KHz)
-Input Signal: 188 KHz, square wave AC, 20 Volts Peak to Peak (Vpp) or 10 Volts Root Main Square (RMS) from a Signal Generator -Capacitors: Unpolarized, in parallel with coil (not mandatory to have capacitor at the transmitter, but increases slightly led brightness) -Coils: length=5 meters, diameter=1 mm, single wire, single layer, cylinder diameter= 12 cm, speaker cable for both transmitter & receiver (coil shape matters !!!) -LED: 1 bright 3Volt white LED at the receiver coil -Resonance occurs at more frequencies: 16, 20, 26, 36, 59, 188 KHZ (led is brightest at 188 KHz)
Subscribe to:
Posts (Atom)